After puffing, the material temperature and moisture is relatively high, in order to ensure product quality and ease of operation, must be rapidly cooled. Extruder discharge of extruded corn currently is the main way the template material, geometric size is relatively large, select flap counterflow cooler or barrel-type cooler.Turning plate counterflow cooler small footprint but a higher height, barrel cooler height low is an area of relatively large.Coolers can be combined according to their production capacity and site space height space allocation.Normally cooler is shipped without the blower and turn off the wind, cooler manufacturer to fit fan and turn off the wind.Generally, at the fan outlet must be located an air volume regulating valve and cooling of materials with different characteristics and at installation time, Chakroun best asbestos duct insulation, prevent condensate ventilation network congestion caused by the winter.
Extruded materials after crushed again.Due to the relatively larger materials by the swelling size, in order to facilitate the next batching, mixing and working, material has to be crushed again.This grinding is very simple, very low energy consumption, than raw material mill power mill.
See more feed processing equipment from our website: http://www.toppelletmachine.com/production-line/
2014年12月29日星期一
2014年12月22日星期一
Feed processing mixer correct using methods and maintenance
Feed processing mixer proper use and maintenance, feed processing mixer application farming industry is very important, of course, in order to make animal feed mixer better play its role, it is necessary for its proper use, and maintenance.
1, before using the machine, check to deal with the whole conduct full pack, adjust the belt tension, and then plug in the power, press the mark direction of change.
2, scheduling press round "clamping screw" to between 0.1-0.3 mm pressure wheel with the template.
3, take the test machine 15 kg of powder, preferably with bran, bran, or 5 pounds of peanut and wheat skin 15 kg of meat, pressure test, repeat the rolling squeeze 15 minutes, the pressure not to feed the template hole vise clamp nail to get through, and then squeeze until the normal discharge. If the user pressed a recipe not feed, feed material then die hole open, flat die surface can put some food oil, then bran or bran feed peanuts meat and wheat skin press out above, and then participate repeat sand squeeze 10 minutes, until the normal discharge.
4, the pellets can be scheduled record length cutter down position.
5, if the exchange template can be removed to remove the barrel containing the hopper, remove the pressure roller and cutter, twist off the cap on the spindle gongs, with accessories "Rally" hanging out flat die.
6, in order to secure the production, when the lid is removed, it is necessary to break the power switch to turn off the machine, and other things to hand contact pressure wheel template.
7, when the machine rolled to two kilograms of pressure wheel removed for cleaning maintenance of copper oil, once every six months to maintain full refueling.
8,105A single-phase motor, please ensure that 220V voltage.
9, please use the equipment grounding great motor equipment.
10, the use of the motor model, the customer has the necessary equipment protection devices.
The process of re-use must pay attention to the above operations, and better maintenance, the only way to more long-term use.
1, before using the machine, check to deal with the whole conduct full pack, adjust the belt tension, and then plug in the power, press the mark direction of change.
2, scheduling press round "clamping screw" to between 0.1-0.3 mm pressure wheel with the template.
3, take the test machine 15 kg of powder, preferably with bran, bran, or 5 pounds of peanut and wheat skin 15 kg of meat, pressure test, repeat the rolling squeeze 15 minutes, the pressure not to feed the template hole vise clamp nail to get through, and then squeeze until the normal discharge. If the user pressed a recipe not feed, feed material then die hole open, flat die surface can put some food oil, then bran or bran feed peanuts meat and wheat skin press out above, and then participate repeat sand squeeze 10 minutes, until the normal discharge.
4, the pellets can be scheduled record length cutter down position.
5, if the exchange template can be removed to remove the barrel containing the hopper, remove the pressure roller and cutter, twist off the cap on the spindle gongs, with accessories "Rally" hanging out flat die.
6, in order to secure the production, when the lid is removed, it is necessary to break the power switch to turn off the machine, and other things to hand contact pressure wheel template.
7, when the machine rolled to two kilograms of pressure wheel removed for cleaning maintenance of copper oil, once every six months to maintain full refueling.
8,105A single-phase motor, please ensure that 220V voltage.
9, please use the equipment grounding great motor equipment.
10, the use of the motor model, the customer has the necessary equipment protection devices.
The process of re-use must pay attention to the above operations, and better maintenance, the only way to more long-term use.
2014年12月21日星期日
Six methods using in the process of processing and feed processing equipment
Feed processing equipment processing Using the following six ways:
1, cut short long fat: straw, sweet potato vine, grass, hay, vegetables, straw, etc., can be used after feeding livestock need chopped. Cows straw should be cut 2─3 cm; pigs 1─2 cm cut vegetables; sweet potato vine is made about 1 cm. General should be short not long, in order to achieve "Mito inch grass cut, no material also on fat" Feeding effect. If the impurity, such as silt to wash, sieve net.
2, grinding aid digestion: food (grain), sweet potato, cassava for animal feed must be crushed and then fed ground to aid digestion. The thickness of the degree of dispersion should be based on the type of feed and livestock may be. Pigs, cattle feed can be crushed or medium or coarse particles 1─2 mm; chicken feed grain should be ground into a powder. Sweet potato, cassava can be cut into pieces and then dried crushed sweet potato can also be fed beating.
3. Soak the softened: corn, wheat, sorghum, soybean meal and other feed, feed soaked before the best time to use some light salt boiling water to soften and then feed, saving feed, and easy to digest, eating poultry. General feed, water ratio of 1. Length of immersion time, should vary the type of season and feed-in and the hot summer weather soaking time should be short, to prevent rot feed.
4, adjust cooking flavors: beans, peas and soy grain feed, which uses the method of cooking and processing modulation. Practice shows, soybean after cooking, destroyed the soybean antitrypsin, enhanced palatability, improve the digestibility and nutritional value; while increasing the effective soybean protein methionine and cystine, improved biological value protein . But not too long cooking time, usually 50 minutes or so.
5, crisp and sweet roasted: roasting process is primarily a modulation method to concentrate feeding the pig. Grain feed, especially feed grain cereals, after a short time later 130─150 ℃ high temperature furnace, where part of the starch into dextrin, improve the utilization of starch, and can eliminate harmful bacteria, feed sweet, tasty, crispy increased appetite, good feeding effect.
6, silage preservation is good: the green material stored at various cellar, pool, cylinder, under anaerobic conditions for fermentation to produce lactic acid. Guarantees forage nutrients, improve forage utilization and digestibility. And the regulation of the season and off-season forage remaining places, the supply of off-season green sweat effective measures to feed.
1, cut short long fat: straw, sweet potato vine, grass, hay, vegetables, straw, etc., can be used after feeding livestock need chopped. Cows straw should be cut 2─3 cm; pigs 1─2 cm cut vegetables; sweet potato vine is made about 1 cm. General should be short not long, in order to achieve "Mito inch grass cut, no material also on fat" Feeding effect. If the impurity, such as silt to wash, sieve net.
2, grinding aid digestion: food (grain), sweet potato, cassava for animal feed must be crushed and then fed ground to aid digestion. The thickness of the degree of dispersion should be based on the type of feed and livestock may be. Pigs, cattle feed can be crushed or medium or coarse particles 1─2 mm; chicken feed grain should be ground into a powder. Sweet potato, cassava can be cut into pieces and then dried crushed sweet potato can also be fed beating.
3. Soak the softened: corn, wheat, sorghum, soybean meal and other feed, feed soaked before the best time to use some light salt boiling water to soften and then feed, saving feed, and easy to digest, eating poultry. General feed, water ratio of 1. Length of immersion time, should vary the type of season and feed-in and the hot summer weather soaking time should be short, to prevent rot feed.
4, adjust cooking flavors: beans, peas and soy grain feed, which uses the method of cooking and processing modulation. Practice shows, soybean after cooking, destroyed the soybean antitrypsin, enhanced palatability, improve the digestibility and nutritional value; while increasing the effective soybean protein methionine and cystine, improved biological value protein . But not too long cooking time, usually 50 minutes or so.
5, crisp and sweet roasted: roasting process is primarily a modulation method to concentrate feeding the pig. Grain feed, especially feed grain cereals, after a short time later 130─150 ℃ high temperature furnace, where part of the starch into dextrin, improve the utilization of starch, and can eliminate harmful bacteria, feed sweet, tasty, crispy increased appetite, good feeding effect.
6, silage preservation is good: the green material stored at various cellar, pool, cylinder, under anaerobic conditions for fermentation to produce lactic acid. Guarantees forage nutrients, improve forage utilization and digestibility. And the regulation of the season and off-season forage remaining places, the supply of off-season green sweat effective measures to feed.
2014年12月18日星期四
Using six methods of feed processing
1. Cut a short length of fat
Straw, sweet potato vine, grass, hay, vegetables, straw, etc., are required to be used to feed livestock after chopped. Cows straw should be cut 2--3 cm; pigs vegetables cut 1--2 cm; sweet potato vine is made about 1 cm. General should be short not long, in order to achieve "Mito inch grass cut, no material also on fat" Feeding effect. If the impurity, such as silt to wash, sieve net.
2. crushing aid digestion
Food (grain), sweet potato, cassava for animal feed, feed must be crushed and then ground to aid digestion. The thickness of the degree of dispersion should be based on the type of feed and livestock may be. Pigs, cattle feed can be crushed or medium or coarse particles 1--2 mm; chicken feed grain should be ground into a powder. Sweet potato, cassava can be cut into pieces and then dried crushed sweet potato can also be fed beating.
3. Soak the softened
Corn, wheat, sorghum, soybean meal and other feed, feed soaked before the best time to use some light salt boiling water to soften and then feed, saving feed, and easy to digest, eating poultry. General feed, water ratio of 1. Length of immersion time, should vary the type of season and feed-in and the hot summer weather soaking time should be short, to prevent rot feed.
4. Cooking tune taste
Beans, peas and soy grain feed, which uses the method of cooking and processing modulation. Practice shows, soybean after cooking, destroyed the soybean antitrypsin, enhanced palatability, improve the digestibility and nutritional value; while increasing the effective soybean protein methionine and cystine, improved biological value protein . But not too long cooking time, usually 50 minutes or so.
5. Roasted sweet cakes
Roasting process is primarily a modulation method to concentrate feeding the pig. Grain feed, especially feed grain cereals, after a short time after 130--150 ℃ high temperature furnace, where part of the starch into dextrin, improve the utilization of starch, and can eliminate harmful bacteria, feed sweet, tasty, crisp increase appetite, good feeding effect.
6. Good silage preservation
The green material stored at various cellar, pool, cylinder, under anaerobic conditions for fermentation to produce lactic acid. Guarantees forage nutrients, improve forage utilization and digestibility. And the regulation of the season and off-season forage remaining places, the supply of off-season green sweat effective measures to feed.
Straw, sweet potato vine, grass, hay, vegetables, straw, etc., are required to be used to feed livestock after chopped. Cows straw should be cut 2--3 cm; pigs vegetables cut 1--2 cm; sweet potato vine is made about 1 cm. General should be short not long, in order to achieve "Mito inch grass cut, no material also on fat" Feeding effect. If the impurity, such as silt to wash, sieve net.
2. crushing aid digestion
Food (grain), sweet potato, cassava for animal feed, feed must be crushed and then ground to aid digestion. The thickness of the degree of dispersion should be based on the type of feed and livestock may be. Pigs, cattle feed can be crushed or medium or coarse particles 1--2 mm; chicken feed grain should be ground into a powder. Sweet potato, cassava can be cut into pieces and then dried crushed sweet potato can also be fed beating.
3. Soak the softened
Corn, wheat, sorghum, soybean meal and other feed, feed soaked before the best time to use some light salt boiling water to soften and then feed, saving feed, and easy to digest, eating poultry. General feed, water ratio of 1. Length of immersion time, should vary the type of season and feed-in and the hot summer weather soaking time should be short, to prevent rot feed.
4. Cooking tune taste
Beans, peas and soy grain feed, which uses the method of cooking and processing modulation. Practice shows, soybean after cooking, destroyed the soybean antitrypsin, enhanced palatability, improve the digestibility and nutritional value; while increasing the effective soybean protein methionine and cystine, improved biological value protein . But not too long cooking time, usually 50 minutes or so.
5. Roasted sweet cakes
Roasting process is primarily a modulation method to concentrate feeding the pig. Grain feed, especially feed grain cereals, after a short time after 130--150 ℃ high temperature furnace, where part of the starch into dextrin, improve the utilization of starch, and can eliminate harmful bacteria, feed sweet, tasty, crisp increase appetite, good feeding effect.
6. Good silage preservation
The green material stored at various cellar, pool, cylinder, under anaerobic conditions for fermentation to produce lactic acid. Guarantees forage nutrients, improve forage utilization and digestibility. And the regulation of the season and off-season forage remaining places, the supply of off-season green sweat effective measures to feed.
Improve palatability what's a good way
On pig farming, the increased feed intake can maximize meat production and meat quality in feeding should think of ways to improve palatability, and are willing to take the initiative to eat the pigs feed, increased intake.
The use of flavors, studies have shown that pigs for sweets has a very significant preference sweeteners (containing 6.7% of sodium saccharin and other long-lasting flavor enhancers and synergist) can increase feed intake, but added level too high or too low is not conducive to pig feed intake of the play, in piglet growth phase (1 to 28 days), diets 150 mg / kg of compound sweetener can achieve the maximum daily intake, but also can get this biggest daily gain stage. In addition, experiments show that the flavoring agent with antioxidant function, with the extension of feed storage time, flavoring agents can effectively alleviate the degree of oxidation of feed.
Oxidation feed mildew, mold can take the following steps to oxidation:
(1) the storage of feed moisture content should be controlled within a certain range, generally not more than 12%, warehouse ventilation, insulation, ground moisture to do place, the relative humidity at 60% humidity cause mold growth too large, and is not conducive to the preservation of a high fat diet;
(2) the optimum temperature for the growth of mold 28 ~ 38 ℃, so to control the temperature of the warehouse, prevent mildew, highly unsaturated fatty acid in feed at higher temperatures to oxidative rancidity.
(3) the rational use of some antifungal powder and antioxidants to deal with some urgent situations feed moldy and rancid, but it will affect the nutritional value of the feed, it is not recommended for long-term use.
Reasonable process, there were reports that will be made of crushed grain feed pellets, the feed utilization can be increased by about 23%. Feed in the granulation process will go through the process of steam treatment and suppression of the high-pressure rubbing crowded, making feed grain cell rupture and release of intracellular substances to increase the nutritional content of the feed. Meanwhile, after pelletized feed, palatability, and when the feed reduces energy consumption, but also makes the feed more uniform, to avoid some kind of pig feed ingredients designed to pick eating.
Elimination of anti-nutritional factors, anti-nutritional factors are the main factors restricting feed efficiency, in order to reduce or eliminate the effects of anti-nutritional factors, can take a variety of approaches. The main treatment methods include physical treatment, chemical treatment, biological treatment and breeding of new varieties. Most of the anti-nutritional factors have thermal instability, such as a variety of protease inhibitors, lectins, and other anti-vitamin factors, it may be denatured by heating.
The use of flavors, studies have shown that pigs for sweets has a very significant preference sweeteners (containing 6.7% of sodium saccharin and other long-lasting flavor enhancers and synergist) can increase feed intake, but added level too high or too low is not conducive to pig feed intake of the play, in piglet growth phase (1 to 28 days), diets 150 mg / kg of compound sweetener can achieve the maximum daily intake, but also can get this biggest daily gain stage. In addition, experiments show that the flavoring agent with antioxidant function, with the extension of feed storage time, flavoring agents can effectively alleviate the degree of oxidation of feed.
Oxidation feed mildew, mold can take the following steps to oxidation:
(1) the storage of feed moisture content should be controlled within a certain range, generally not more than 12%, warehouse ventilation, insulation, ground moisture to do place, the relative humidity at 60% humidity cause mold growth too large, and is not conducive to the preservation of a high fat diet;
(2) the optimum temperature for the growth of mold 28 ~ 38 ℃, so to control the temperature of the warehouse, prevent mildew, highly unsaturated fatty acid in feed at higher temperatures to oxidative rancidity.
(3) the rational use of some antifungal powder and antioxidants to deal with some urgent situations feed moldy and rancid, but it will affect the nutritional value of the feed, it is not recommended for long-term use.
Reasonable process, there were reports that will be made of crushed grain feed pellets, the feed utilization can be increased by about 23%. Feed in the granulation process will go through the process of steam treatment and suppression of the high-pressure rubbing crowded, making feed grain cell rupture and release of intracellular substances to increase the nutritional content of the feed. Meanwhile, after pelletized feed, palatability, and when the feed reduces energy consumption, but also makes the feed more uniform, to avoid some kind of pig feed ingredients designed to pick eating.
Elimination of anti-nutritional factors, anti-nutritional factors are the main factors restricting feed efficiency, in order to reduce or eliminate the effects of anti-nutritional factors, can take a variety of approaches. The main treatment methods include physical treatment, chemical treatment, biological treatment and breeding of new varieties. Most of the anti-nutritional factors have thermal instability, such as a variety of protease inhibitors, lectins, and other anti-vitamin factors, it may be denatured by heating.
2014年12月17日星期三
Animal feed grinding fineness gnaw determine
Animal feed grinding fineness should vary depending on the type of farming.
Chicken feed should not be too small, because eating chicken pellets or crushed cereal material, with the thickness can be used. Rice, broken rice can be added directly to the granular mixer, grinding fineness wheat, barley at 2.5 mm or less appropriate, corn, rice and soybean material to be processed into a powder. When the soft-shell egg production of laying hens need calcium, calcium ideal feed particles, namely the limestone, shells and other ground sorghum grain particle size, in every night to feed the last time together again feed material. Because the particles of calcium longer residence time in the body of the chicken, the chicken body in favor of absorption and utilization, so calcium effect is good.
Piglet feed with special feed pellets or crushed better, beans and other energy feed can fry feed, pig 25 kg or less, can be fed ordinary pig feed; crushed fine of more than 25 kg pig feed degree can be controlled within 2 mm. Feed pigs, crushing the more detailed the better.
Cattle, fine grinding fineness can feed the sheep more than 2 mm, because cattle can ruminant feed ruminant slightly favor a little rough, improve feed digestibility. In the cow, feed the sheep can be crushed to less than 1 mm, in order to facilitate digestion.
Grinding fineness feed livestock species, taking into account, while also taking into account not so rich in fat feed grains such as corn, oats and other smash too small, too long storage time, to avoid rancidity deterioration.
Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
Chicken feed should not be too small, because eating chicken pellets or crushed cereal material, with the thickness can be used. Rice, broken rice can be added directly to the granular mixer, grinding fineness wheat, barley at 2.5 mm or less appropriate, corn, rice and soybean material to be processed into a powder. When the soft-shell egg production of laying hens need calcium, calcium ideal feed particles, namely the limestone, shells and other ground sorghum grain particle size, in every night to feed the last time together again feed material. Because the particles of calcium longer residence time in the body of the chicken, the chicken body in favor of absorption and utilization, so calcium effect is good.
Piglet feed with special feed pellets or crushed better, beans and other energy feed can fry feed, pig 25 kg or less, can be fed ordinary pig feed; crushed fine of more than 25 kg pig feed degree can be controlled within 2 mm. Feed pigs, crushing the more detailed the better.
Cattle, fine grinding fineness can feed the sheep more than 2 mm, because cattle can ruminant feed ruminant slightly favor a little rough, improve feed digestibility. In the cow, feed the sheep can be crushed to less than 1 mm, in order to facilitate digestion.
Grinding fineness feed livestock species, taking into account, while also taking into account not so rich in fat feed grains such as corn, oats and other smash too small, too long storage time, to avoid rancidity deterioration.
Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
2014年12月11日星期四
The third layer structure of Strongwin model plant
pellet feed unit increase the particle section on the basis of producing powder feed compelete sets of equipment.
particles section equipment mainly includes particle machine,cooler, crushed machine, grader,packaging scale etc.
particles section equipment mainly includes particle machine,cooler, crushed machine, grader,packaging scale etc.
The fourth layer structure of Strongwin model plant
Henan Strongwin follows the ideals of "Customers Oriented, Common Development". We are making great efforts to offer high quality feedstuff machines, biomass energy grinding machines and organic fertilizer machines. We can make coal and biomass into energy.
The fifth layer structure of Strongwin model plant
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
The fifth layer structure of Strongwin model plant
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
2014年12月3日星期三
Chicken feed formulation
First,feed mix
1. Diversification feed, pig feed generally consists of energy feed, protein feed, mineral feed, vitamins feed four composed of various types of feed as much as possible when using several, in order to improve the efficiency and utilization of the full price of feed.
2. Feed the appropriate volume, the energy content per kg of feed concentration should be appropriate, excessive eating pig waste, and even reach satiety; low feed volume is too large, eat so much energy and nutrients will not be met .
3, the control of crude fiber content, better palatability, digestible crude fiber affect palatability, digestion and absorption, an important factor in feed conversion, generally crude fiber content of not more than 6% to 8%.
4, as far as possible the use of local feed to reduce costs.
5, appropriate to add trace elements, vitamins and anti-bacterial growth agent.
Second, feed modulation
1, ground grain, corn, etc. should be crushed.
2, raw and cooked feed generally feed raw feed, but beans and other feed if feed hemp taste bitter, poisonous feed and restaurants close to the leftovers and tuber root class feed to be fried or cooked.
3, raw wet spices have a very fine dust or wet feed raw spices best to avoid feed into the respiratory tract. 1:0.5 watered amount to 1.5.
Thank you very much concerned about our content, if you want to customize the production and processing of feed, please contact us. Our factory can provide comprehensive, complete sets of feed pellet production line according to your needs.
1. Diversification feed, pig feed generally consists of energy feed, protein feed, mineral feed, vitamins feed four composed of various types of feed as much as possible when using several, in order to improve the efficiency and utilization of the full price of feed.
2. Feed the appropriate volume, the energy content per kg of feed concentration should be appropriate, excessive eating pig waste, and even reach satiety; low feed volume is too large, eat so much energy and nutrients will not be met .
3, the control of crude fiber content, better palatability, digestible crude fiber affect palatability, digestion and absorption, an important factor in feed conversion, generally crude fiber content of not more than 6% to 8%.
4, as far as possible the use of local feed to reduce costs.
5, appropriate to add trace elements, vitamins and anti-bacterial growth agent.
Second, feed modulation
1, ground grain, corn, etc. should be crushed.
2, raw and cooked feed generally feed raw feed, but beans and other feed if feed hemp taste bitter, poisonous feed and restaurants close to the leftovers and tuber root class feed to be fried or cooked.
3, raw wet spices have a very fine dust or wet feed raw spices best to avoid feed into the respiratory tract. 1:0.5 watered amount to 1.5.
Thank you very much concerned about our content, if you want to customize the production and processing of feed, please contact us. Our factory can provide comprehensive, complete sets of feed pellet production line according to your needs.
2014年11月24日星期一
SZLH 420 gear ring die pellet mill (SZLH 420 type)
● SZLH420 ring die pellet mill using high-precision direct drive gear, transmission rate, job stability, and ensure maximum energy transfer, production increased by 15% -20% over the belt drive.
● All stainless steel door. Has a machine outside the body and nestingobservation window, easy to operate.
● suppress indoor double guide roller, with high-quality alloy steel with international advanced processing technology of the ring mold or stainless steel ring mold, ring mold using positioning quick release mechanism hoop replacement quick and easy.
● machine transmission key positions imported bearings, seals, long service life, low noise.
● Full stainless steel feeder, variable pitch anti-arching structure, frequency control.
● plus a large stainless steel conditioner, using axial feed steam, greatly enhance the effect of quenching and aging time.
● cabinet imported machining center, high precision gap.
● precision drive gear and pinion carburizing sudden fire, hardened grinding teeth Machining, smooth transmission, low noise, long life.
● machine with iron and overload protection device, give full consideration to the use of the process to protect the host.
● using the new snake-type spring couplings compensate large, more stable operation.
● can be equipped with single, double, multi-jacketed conditioner or biaxial differential diameter conditioner, to meet the production of high-grade materials and aquatic livestock feed different needs.
● All stainless steel door. Has a machine outside the body and nestingobservation window, easy to operate.● suppress indoor double guide roller, with high-quality alloy steel with international advanced processing technology of the ring mold or stainless steel ring mold, ring mold using positioning quick release mechanism hoop replacement quick and easy.
● machine transmission key positions imported bearings, seals, long service life, low noise.
● Full stainless steel feeder, variable pitch anti-arching structure, frequency control.
● plus a large stainless steel conditioner, using axial feed steam, greatly enhance the effect of quenching and aging time.
● cabinet imported machining center, high precision gap.
● precision drive gear and pinion carburizing sudden fire, hardened grinding teeth Machining, smooth transmission, low noise, long life.
● machine with iron and overload protection device, give full consideration to the use of the process to protect the host.
● using the new snake-type spring couplings compensate large, more stable operation.
● can be equipped with single, double, multi-jacketed conditioner or biaxial differential diameter conditioner, to meet the production of high-grade materials and aquatic livestock feed different needs.
2014年11月18日星期二
The reason of pellet feed abnormal appearance produced and improvement measures (1)
A single particle or particle color inconsistencies between individuals, commonly known as "flower material" this kind of situation is relatively common in the production of aquatic feed, mainly for the individual pellets from the ring die in color than the other normal particle color deep or shallow, surface color or a single particle are inconsistent, thus affecting the appearance of the whole batch of feed quality.
The reasons of this phenomenon are mainly in the following aspects:
1, because of the complex component of aquatic feed formula, raw material variety, some ingredients quantity is relatively small, in the mixture of raw materials, if the mixing effect of mixing machine is not ideal, it is difficult to ensure that raw material is mixed into the granulator is uniform, thereby the quenching and tempering and granulation process, common role in the water, temperature and pressure, raw material physical and chemical changes occur, resulting in material color change of different components are not consistent, produce "flower material", in this case in feed formulations containing change material color change of temperature and moisture sensitive when the comparison is more outstanding.
2, the raw material for the moisture content of granulation is inconsistent. In the process of aquatic feed production, often in order to make up for the loss of raw water after super fine crushing, to add a certain amount of water in the mixer, mixing before entering the conditioner for Quenched and tempered. Some feed manufacturers, technology is relatively simple, directly into a certain amount of water in a mixing machine, instead of using special nozzle spray, so it is difficult to feed in the mixed water can be evenly distributed. When the mixed raw material into the conditioner conditioning conditioner, because it is impossible in a short period of time so that the water further distribution, in the role of steam, feed in various parts after quenching and tempering curing effect is not consistent, after granulation color change is not consistent.
3, to be with the repeated granulation granulation chamber in the back of the machine. Pelletized granule materials after cooling and sieving can be finished material, fine powder or small particles of screening, often re entered the granulation process, usually into the mixing machine or be pelleting bin, because this is the material re conditioning and granulation, the modified if and other raw materials mixed unevenly or inclusions are back to the small particles, for some feed formulation, can sometimes have a "flower material".
4, diameter of die hole wall roughness is not consistent. Because the mould hole finish inconsistency by particles during extrusion resistance and the extrusion pressure is not the same, the color change is not consistent. In addition, some ring die with small hole on the wall has a burr, particles will scratch the surface in the extrusion, resulting in different surface color of single particle. For the four generation "listed above flower material" reasons, the improved measures have been very clear, mainly lies in the hybrid control of each component in the mixed formulation of the uniformity and the added moisture uniformity; improve the conditioning performance, control conditioning temperature when necessary, using quenched and tempered low temperature to reduce some of the color change; control back to the machine, for easy to produce the "flower" formula, as far as possible not to machine material direct granulation, should be put back to the machine and re mixing the raw materials after crushing; adopts the ring mold quality has safeguard, control die hole finish, when necessary to the die hole sanding after use.
In short, granule material for abnormal appearance in feed production, discussed above, seven kinds of representative forms, and exceptional appearance some particles due to not representative, not listed here are discussed. Discussion as can be seen from the above, the cause of these phenomena are in many aspects, each other is not completely isolated, which requires us to deal with such problems in the practical work, should add analysis, grasp the crux of the problem, it can solve the problem.
The reasons of this phenomenon are mainly in the following aspects:
1, because of the complex component of aquatic feed formula, raw material variety, some ingredients quantity is relatively small, in the mixture of raw materials, if the mixing effect of mixing machine is not ideal, it is difficult to ensure that raw material is mixed into the granulator is uniform, thereby the quenching and tempering and granulation process, common role in the water, temperature and pressure, raw material physical and chemical changes occur, resulting in material color change of different components are not consistent, produce "flower material", in this case in feed formulations containing change material color change of temperature and moisture sensitive when the comparison is more outstanding.
2, the raw material for the moisture content of granulation is inconsistent. In the process of aquatic feed production, often in order to make up for the loss of raw water after super fine crushing, to add a certain amount of water in the mixer, mixing before entering the conditioner for Quenched and tempered. Some feed manufacturers, technology is relatively simple, directly into a certain amount of water in a mixing machine, instead of using special nozzle spray, so it is difficult to feed in the mixed water can be evenly distributed. When the mixed raw material into the conditioner conditioning conditioner, because it is impossible in a short period of time so that the water further distribution, in the role of steam, feed in various parts after quenching and tempering curing effect is not consistent, after granulation color change is not consistent.
3, to be with the repeated granulation granulation chamber in the back of the machine. Pelletized granule materials after cooling and sieving can be finished material, fine powder or small particles of screening, often re entered the granulation process, usually into the mixing machine or be pelleting bin, because this is the material re conditioning and granulation, the modified if and other raw materials mixed unevenly or inclusions are back to the small particles, for some feed formulation, can sometimes have a "flower material".
4, diameter of die hole wall roughness is not consistent. Because the mould hole finish inconsistency by particles during extrusion resistance and the extrusion pressure is not the same, the color change is not consistent. In addition, some ring die with small hole on the wall has a burr, particles will scratch the surface in the extrusion, resulting in different surface color of single particle. For the four generation "listed above flower material" reasons, the improved measures have been very clear, mainly lies in the hybrid control of each component in the mixed formulation of the uniformity and the added moisture uniformity; improve the conditioning performance, control conditioning temperature when necessary, using quenched and tempered low temperature to reduce some of the color change; control back to the machine, for easy to produce the "flower" formula, as far as possible not to machine material direct granulation, should be put back to the machine and re mixing the raw materials after crushing; adopts the ring mold quality has safeguard, control die hole finish, when necessary to the die hole sanding after use.
In short, granule material for abnormal appearance in feed production, discussed above, seven kinds of representative forms, and exceptional appearance some particles due to not representative, not listed here are discussed. Discussion as can be seen from the above, the cause of these phenomena are in many aspects, each other is not completely isolated, which requires us to deal with such problems in the practical work, should add analysis, grasp the crux of the problem, it can solve the problem.
Henan Strongwin feed machinery factory is a set research and development, manufacturing, sales and service in one,specialized in feed machinery complete sets of engineering R & D and manufacturing, engineering design and installation, can be customized according to user needs!
2014年10月28日星期二
Animal winter supplements vitamins
The winter season, the lack of green feed, livestock and poultry prone to vitamin deficiency. Vitamin requirements in various livestock body although very little, but it is the organic compounds necessary to maintain the normal physiological function of the animal body. The lack of time, the growth of livestock and poultry in stunted growth, productivity, and even disease.
Vitamin A vitamin A can maintain a healthy and normal physiological function of various organ systems mucosal epithelial tissues, normal vision and reproductive function to maintain cattle. Lack of vitamin A can cause a series of epithelial tissues weakened ability to resist diseases and pregnancy diseases, such as abortion, stillbirth. Should be timely supplement of vitamin A in the following cases: forage to straw based; hay cream after the harvest; pure corn silage (or even break rod after corn), corn and other feed （It is best to use concentrate feed machinery processing, ease of nutrition collocation.）varieties the proportion is low; colostrum and ordinary milk feeding amount is insufficient, early weaned calves, self prepared in artificial milk; in heat stress, transportation supplement is necessary, generally 0.5 to 1 times the amount of complement.
The main function of vitamin D vitamin D is to adjust the calcium and phosphorus absorption, metabolism and skeletal growth, vitamin D deficiency can cause rickets and calf cartilage disease of cow. Is generally believed that the requirement of calves and cattle growth to 100 kg of body weight per 660 international units. Lactating cows per kilogram of body weight 30 international units. Lactating cows prenatal (especially high-yielding cows) from half a month to start prenatal injection of vitamin A, D, E mixed formulation, can significantly effect on prevention of postpartum disease.
The main effect of vitamin E and vitamin E is a biological antioxidant and free radical scavenging effect, can improve the cellular and humoral immune response. Lack of vitamin E in calf muscle dystrophy characterized, adult cattle from natural feed can obtain sufficient quantity. Long term storage to feed its vitamin E content decreased with the prolonging of the storage time. In feeding, calves per kg diet dry matter required 25 to 40 international units, lactating cows 15 international units.
Water soluble B vitamins thiamine, riboflavin, pyridoxine, including biotin, niacin, vitamin B12, choline, to the physiological metabolism plays a certain role. But the rumen microbial cattle can be synthesized, calves rumen development normal before the B vitamins supply from milk. Therefore, to feed cows milk heating should notice when, generally within 40 DEG C advisable.
Vitamin A vitamin A can maintain a healthy and normal physiological function of various organ systems mucosal epithelial tissues, normal vision and reproductive function to maintain cattle. Lack of vitamin A can cause a series of epithelial tissues weakened ability to resist diseases and pregnancy diseases, such as abortion, stillbirth. Should be timely supplement of vitamin A in the following cases: forage to straw based; hay cream after the harvest; pure corn silage (or even break rod after corn), corn and other feed （It is best to use concentrate feed machinery processing, ease of nutrition collocation.）varieties the proportion is low; colostrum and ordinary milk feeding amount is insufficient, early weaned calves, self prepared in artificial milk; in heat stress, transportation supplement is necessary, generally 0.5 to 1 times the amount of complement.
The main function of vitamin D vitamin D is to adjust the calcium and phosphorus absorption, metabolism and skeletal growth, vitamin D deficiency can cause rickets and calf cartilage disease of cow. Is generally believed that the requirement of calves and cattle growth to 100 kg of body weight per 660 international units. Lactating cows per kilogram of body weight 30 international units. Lactating cows prenatal (especially high-yielding cows) from half a month to start prenatal injection of vitamin A, D, E mixed formulation, can significantly effect on prevention of postpartum disease.
The main effect of vitamin E and vitamin E is a biological antioxidant and free radical scavenging effect, can improve the cellular and humoral immune response. Lack of vitamin E in calf muscle dystrophy characterized, adult cattle from natural feed can obtain sufficient quantity. Long term storage to feed its vitamin E content decreased with the prolonging of the storage time. In feeding, calves per kg diet dry matter required 25 to 40 international units, lactating cows 15 international units.
Water soluble B vitamins thiamine, riboflavin, pyridoxine, including biotin, niacin, vitamin B12, choline, to the physiological metabolism plays a certain role. But the rumen microbial cattle can be synthesized, calves rumen development normal before the B vitamins supply from milk. Therefore, to feed cows milk heating should notice when, generally within 40 DEG C advisable.
How to develop an appropriate breeding program
If possible, requires weighing the technical staff present, and promptly correct the existence of the subject, to ensure the reliability of weighing and promptly calculate the results weighed. The second is to ensure that there is an equal flocks foraging opportunities and a relatively chaotic environment which fed the feed materials required to do a black light to teach a fast turn feed rate and the best use of automatic feeding of such farming equipment; for large Dutch feed line is to consider adding vice bins and bins of equal parts of the sub-feed line; general requirement is expected within 150 seconds can connect more ideal, while ensuring Ingredients box and vice bins spout the same, and according to the amount of feed and change the way of feeding the material to adjust the size of the mouth, and the material transfer time.
The results should be based on pre-column and choose to stay weight, while changes in the seasons to develop a set of reference affordable restricted feeding program, usually in 7-13 weeks using four three-restricted feeding; at 14-18 weeks with five two restricted feeding; at 19-22 weeks using sixty-one restricted feeding, and finally with daily feeding mode. Because the weight of the flock is mainly based on the incubation period of feeding, so necessary to really do the daily work load.
Experience has shown that in Canada the best light for chickens after the daily feeding methods are taught using large benefits, especially in the winter flocks are more favorable to do so for less stress in chickens, chickens produce beneficial function display However, if this method should be adjusted breeding program. In addition to ensure the normal operation of feeding equipment, the requirements necessary to do routine inspections and maintenance work, especially when cleaning up the house a variety of equipment necessary to focus on the care, inspection and maintenance work, the third is to ensure the correctness and preparation the average resistance, probably because of the subjective prevent errors caused.
Second, control the feeding method used to determine the column density of one and the material level based on the number of chickens into the house; we hope to create a better bar chicks fed premise, and believe that the material level as possible, However, the actual result is more chick bar its average degree worse, so we in the general layout of the material level of 12 bar by a large chicken, chick bar is 13, if the material level is still wealthy, then rather be sealed . First day restricted feeding weighing, weighing time and place must ensure that weighing is relatively fixed, and for the subsequent laying period weighed lay the foundation to develop good habits; the second is the proportion of chickens weighing more than 10%, at least; the third is to ensure proper weighing equipment, which requires weighing before weighing equipment necessary to calibrate and ensure accurate readings and weighing number.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
The results should be based on pre-column and choose to stay weight, while changes in the seasons to develop a set of reference affordable restricted feeding program, usually in 7-13 weeks using four three-restricted feeding; at 14-18 weeks with five two restricted feeding; at 19-22 weeks using sixty-one restricted feeding, and finally with daily feeding mode. Because the weight of the flock is mainly based on the incubation period of feeding, so necessary to really do the daily work load.
Experience has shown that in Canada the best light for chickens after the daily feeding methods are taught using large benefits, especially in the winter flocks are more favorable to do so for less stress in chickens, chickens produce beneficial function display However, if this method should be adjusted breeding program. In addition to ensure the normal operation of feeding equipment, the requirements necessary to do routine inspections and maintenance work, especially when cleaning up the house a variety of equipment necessary to focus on the care, inspection and maintenance work, the third is to ensure the correctness and preparation the average resistance, probably because of the subjective prevent errors caused.
Second, control the feeding method used to determine the column density of one and the material level based on the number of chickens into the house; we hope to create a better bar chicks fed premise, and believe that the material level as possible, However, the actual result is more chick bar its average degree worse, so we in the general layout of the material level of 12 bar by a large chicken, chick bar is 13, if the material level is still wealthy, then rather be sealed . First day restricted feeding weighing, weighing time and place must ensure that weighing is relatively fixed, and for the subsequent laying period weighed lay the foundation to develop good habits; the second is the proportion of chickens weighing more than 10%, at least; the third is to ensure proper weighing equipment, which requires weighing before weighing equipment necessary to calibrate and ensure accurate readings and weighing number.
Aquatic feed prices reflect competitive market
For freshwater fish feed prices in early August, I think it was a combination of conventional price behavior, or some manufacturers marketing strategy, or intentional. From raw materials decline, the price has not yet reached the degree. As can be seen from the price cuts, more intense competition in the industry trend, in order to compete and restore the market, at any price, a variety of marketing tools also varied.
Finished feed normal price for the whole chain especially for frontline farmers is a good thing, farmers can reduce costs, reduce their burden, as has the responsibility of manufacturers, and farmers should work hand in hand. But if unconventional prices in the long run is not necessarily a good thing for farmers, fleece. Feed price changes, more dependent on raw material prices, if there is no significant fluctuations in raw material prices, and manufacturers for certain factors deliberate, then it might disrupt the entire market rule. Raw material price cuts did not reach the price of the line, if you must go to the price, the manufacturers have no way to maintain a normal level of profit, the result will be what happens? Either a loss or making a fuss in product quality, if making a fuss about quality, eventually leading to poor development of the industry, or the expense of innocent farmers.
Many manufacturers are now referred to the sustainable development of this topic, but the behavior is often intentionally or unintentionally deviate from this direction. Really help farmers make the healthy development of the industry, not by a simple price war, more needs to think about how to better help farmers make money. Especially in the current high-temperature diseases, they need more guidance technology, reduce mortality, teach a man to fish than giving the fishing is the truth. Good feed products, the same can reduce the pollution of the water quality, reduce fish hepatobiliary damage, so feed mill products to adhere to be able to do the farmers, but also a way to help them.
Now soybean meal, rapeseed meal price although some decline, but only slightly, corn is also a substantial price rise, wheat and some other raw materials modest rise, DDGS tight spot. Before ordering a lot of manufacturers have a lot of futures, have not yet digested, cost pressure is very great. For Guangdong, we combine procurement method is to use futures spot mode, the relative industry prices still have an advantage, so this price, we are pleased to face, we will stand in the ranks of farmers, the quality will continue on a steady basis upgrade. It is also our responsibility to the industry has been in Guangdong, the quality of the winning attitude, so we expected this year, sales of freshwater fish in the doldrums environment super typhoon, high disease, can buck the trend growth in sales, up more than 100%.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
Finished feed normal price for the whole chain especially for frontline farmers is a good thing, farmers can reduce costs, reduce their burden, as has the responsibility of manufacturers, and farmers should work hand in hand. But if unconventional prices in the long run is not necessarily a good thing for farmers, fleece. Feed price changes, more dependent on raw material prices, if there is no significant fluctuations in raw material prices, and manufacturers for certain factors deliberate, then it might disrupt the entire market rule. Raw material price cuts did not reach the price of the line, if you must go to the price, the manufacturers have no way to maintain a normal level of profit, the result will be what happens? Either a loss or making a fuss in product quality, if making a fuss about quality, eventually leading to poor development of the industry, or the expense of innocent farmers.
Many manufacturers are now referred to the sustainable development of this topic, but the behavior is often intentionally or unintentionally deviate from this direction. Really help farmers make the healthy development of the industry, not by a simple price war, more needs to think about how to better help farmers make money. Especially in the current high-temperature diseases, they need more guidance technology, reduce mortality, teach a man to fish than giving the fishing is the truth. Good feed products, the same can reduce the pollution of the water quality, reduce fish hepatobiliary damage, so feed mill products to adhere to be able to do the farmers, but also a way to help them.
Now soybean meal, rapeseed meal price although some decline, but only slightly, corn is also a substantial price rise, wheat and some other raw materials modest rise, DDGS tight spot. Before ordering a lot of manufacturers have a lot of futures, have not yet digested, cost pressure is very great. For Guangdong, we combine procurement method is to use futures spot mode, the relative industry prices still have an advantage, so this price, we are pleased to face, we will stand in the ranks of farmers, the quality will continue on a steady basis upgrade. It is also our responsibility to the industry has been in Guangdong, the quality of the winning attitude, so we expected this year, sales of freshwater fish in the doldrums environment super typhoon, high disease, can buck the trend growth in sales, up more than 100%.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
2014年10月27日星期一
Preparations before the sheep fattening
Preparations before the sheep fattening
2.1 built sheep pens, feeding sheep pens to be built and more adequate venue. Sheepfold homes to have sunstroke, cold function, select the higher ground, sunny, dry, well-ventilated and sheltered, drainage easy place. The scale of hours, can be built in a residential hospital or nearby, to facilitate management and care. Large scale, it is best to build sheep cell in a place away from the villages, in order to vaccination.
Area sheep rearing sheep quantity. The average area of each sheep is usually 0.8 to 1.2 square meters. Ram, ewe area to be bigger, bred sheep, lambs can be smaller, fine-wool sheep, semi-wool sheep to be bigger, goats should be smaller. Generally sheep height of 2.5 m, a width of not less than 1.5 meters doors, windows, height from the ground is not less than 1.5 meters, to ensure good lighting and ventilation, windows and doors with wood materials as well. Span of 7 to 8 meters, according to the fire safety requirements Each sheep length should not exceed 30 meters.
Pens for brick, facing south, rectangular layout. Winter time can be barricaded plastic greenhouses, about to be shed at the top of each left a vent to prevent greenhouse humidity is too high.
To the front of pens Playground, playground area is 2 to 4 times the area of the sheep. To place the fixed stadium in the middle sink or basin for sheep drinking. Four weeks or to be placed in the middle of fixed or mobile manger manger. Fixed manger with cement or bricks, to be on the narrow groove width, bottom round, mobile manger made of wood.
2.2 ample supply of forage, forage is the material basis of sheep fattening. Fattening sheep feed grass must first be resolved through four ways: First, the full collection of locally produced peanut vine, sweet potato vine, tree leaves, poplar leaves and other high nutrient seedlings vine and leaves. Second, silage and Microbial. If the straw and dried corn stalks can be Microbial. After the fall harvest of corn stalks should be promptly put chopped green silage. Third, the use of bad slag by-products such as distillers grains, tofu, powder residue and the like. Fourth, planting alfalfa, winter grazing 70- rye, grain amaranth and other high-quality forage.
2.3 selected varieties, feeding sheep in conjunction with local production actually choose adapted to local ecological conditions, high production performance, product quality, breeding cycle is short, high economic efficiency of varieties. There are many breeds of sheep and goats feeding adaptation, purely from the perspective of feeding, feeding sheep meat effect is more obvious. Boer goats and goats generally used in Saanen dairy goat, hybrids local goat; sheep to choose Charolais, Dorset, Suffolk, German Mutton Merino sheep and Han sheep or local sheep the hybrid offspring.
2.4 fattening sheep selection and group general, young sheep sheep gain weight faster than aging, good finishing results. Lamb 1-8 months of age the fastest growth, and mainly grow muscles, select weaned lambs do fattening sheep, produce fat lamb meat, and high efficiency. Therefore, usually after weaning identified cluster, the unsuitable reserved for breeding lambs, by gender, body weight, respectively, the group size, grouping fattening. Elimination of adult sheep, by age, body weight, respectively, the group size fattening.
2.5 castration, sterilization and deworming after castrated lambs generally easy to manage, tender meat and the smell of light. Do a good job cleaning pens, disinfection, good health fattening period, can effectively prevent the incidence of sheep fattening period. Sheep get rid of internal and external parasites, to reduce the impact of parasitic diseases is an important measure to ensure good finishing results. Anthelmintic have nitrate chlorophenol, bithionol, albendazole and so on. These drugs were 4 mg per kg body weight, 35 to 75 ml, 2.5 to 3 mg orally effective anthelmintic.
2.6 shoe repair, sheep hoof deformity causing difficulties in walking, the impact of feed, especially in terms of grazing sheep, will seriously affect its performance. Therefore, before finishing orthopedic shoe repair response to the flock.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of sheep feed pellet machine for sheep farm, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
2.1 built sheep pens, feeding sheep pens to be built and more adequate venue. Sheepfold homes to have sunstroke, cold function, select the higher ground, sunny, dry, well-ventilated and sheltered, drainage easy place. The scale of hours, can be built in a residential hospital or nearby, to facilitate management and care. Large scale, it is best to build sheep cell in a place away from the villages, in order to vaccination.
Area sheep rearing sheep quantity. The average area of each sheep is usually 0.8 to 1.2 square meters. Ram, ewe area to be bigger, bred sheep, lambs can be smaller, fine-wool sheep, semi-wool sheep to be bigger, goats should be smaller. Generally sheep height of 2.5 m, a width of not less than 1.5 meters doors, windows, height from the ground is not less than 1.5 meters, to ensure good lighting and ventilation, windows and doors with wood materials as well. Span of 7 to 8 meters, according to the fire safety requirements Each sheep length should not exceed 30 meters.
Pens for brick, facing south, rectangular layout. Winter time can be barricaded plastic greenhouses, about to be shed at the top of each left a vent to prevent greenhouse humidity is too high.
To the front of pens Playground, playground area is 2 to 4 times the area of the sheep. To place the fixed stadium in the middle sink or basin for sheep drinking. Four weeks or to be placed in the middle of fixed or mobile manger manger. Fixed manger with cement or bricks, to be on the narrow groove width, bottom round, mobile manger made of wood.
2.2 ample supply of forage, forage is the material basis of sheep fattening. Fattening sheep feed grass must first be resolved through four ways: First, the full collection of locally produced peanut vine, sweet potato vine, tree leaves, poplar leaves and other high nutrient seedlings vine and leaves. Second, silage and Microbial. If the straw and dried corn stalks can be Microbial. After the fall harvest of corn stalks should be promptly put chopped green silage. Third, the use of bad slag by-products such as distillers grains, tofu, powder residue and the like. Fourth, planting alfalfa, winter grazing 70- rye, grain amaranth and other high-quality forage.
2.3 selected varieties, feeding sheep in conjunction with local production actually choose adapted to local ecological conditions, high production performance, product quality, breeding cycle is short, high economic efficiency of varieties. There are many breeds of sheep and goats feeding adaptation, purely from the perspective of feeding, feeding sheep meat effect is more obvious. Boer goats and goats generally used in Saanen dairy goat, hybrids local goat; sheep to choose Charolais, Dorset, Suffolk, German Mutton Merino sheep and Han sheep or local sheep the hybrid offspring.
2.4 fattening sheep selection and group general, young sheep sheep gain weight faster than aging, good finishing results. Lamb 1-8 months of age the fastest growth, and mainly grow muscles, select weaned lambs do fattening sheep, produce fat lamb meat, and high efficiency. Therefore, usually after weaning identified cluster, the unsuitable reserved for breeding lambs, by gender, body weight, respectively, the group size, grouping fattening. Elimination of adult sheep, by age, body weight, respectively, the group size fattening.
2.5 castration, sterilization and deworming after castrated lambs generally easy to manage, tender meat and the smell of light. Do a good job cleaning pens, disinfection, good health fattening period, can effectively prevent the incidence of sheep fattening period. Sheep get rid of internal and external parasites, to reduce the impact of parasitic diseases is an important measure to ensure good finishing results. Anthelmintic have nitrate chlorophenol, bithionol, albendazole and so on. These drugs were 4 mg per kg body weight, 35 to 75 ml, 2.5 to 3 mg orally effective anthelmintic.
2.6 shoe repair, sheep hoof deformity causing difficulties in walking, the impact of feed, especially in terms of grazing sheep, will seriously affect its performance. Therefore, before finishing orthopedic shoe repair response to the flock.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of sheep feed pellet machine for sheep farm, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
2014年10月23日星期四
Feed formulation design ideas
Feed formulation design work is a very interesting, very logical work, but also contains many things dialectical method. Not simply a recipe to several raw materials mixed together, not only the need for animal physiology, biochemistry, organic chemistry have in-depth understanding, but also on raising standards, types and characteristics of feed materials using nutrients lies at the chest while keeping the flexibility to apply criteria based on the actual situation. Here is the recipe I have time to do some feelings and experiences in a feed mill for you peer reference.
Quality must be noted that the palatability of feed and raw materials
Some formulators do feed formulation, the only mechanical input to the various feed ingredients to the recipe software, and then click on the "linear programming", as long as the formula of nutrients out of reach, and put the recipe and then submitted to a print production on needed. In fact, doing so is extremely irresponsible, although nutritional supplements reached, but feed the "customers" of animals like it or not is really important. Because poor palatability of feed, animal feed will be little or simply refuse to eat. Therefore, selection of raw materials must choose palatability, no deterioration of fresh raw materials. Formulators should not just do a day in the office at the computer to do recipes, each feed must be done in person before a group to look at the quality of raw materials, the necessary time to personally taste raw palatability. There is a feed made out when you want to test it after feed color, smell whether standards. Some feed mills often like to do some anti-stress, and increase lean meat, and promote animal growth of special packet of materials, because relatively speaking, than the obvious effect of this packet of materials, the profit is relatively high. For example, once I do a control mosquito breeding farm parcels material, the main component of this small material called cyromazine, the main role is used to kill mosquitoes eggs. When do such small material cyromazine did not notice the smell is quite unpleasant, just add some carriers and antibiotics in the recipe. The results reflect the customer antifeeding added this little pig feed material, then adjust the recipe when added flavors and sweeteners, then the market reflects this small material has been very good. Another time a similar thing is that some customers complain about our company a small material (main ingredient is yellow amines and amine synergists yellow) growth-promoting effect is not good, then it has increased the amount of two sulfonamides and trimethoprim times, to keep up with examples like the result, or refuse to eat such a small animal feed, the reason is very simple, because these drugs additives have been bad taste and palatability, the time when the amount of the increase will inevitably increase the unpleasant taste, so the sulfonamides and trimethoprim amount to 1.5 times the original amount, but also adds some flavor, so that the effect will be much better formulations.
Stress that it is important to note the quality of feed ingredients, such as rice bran, wheat bran and other raw materials. Fresh rice bran will have a fragrance smells taste in your mouth sweet side, inside a green shell in general are fresh bran rice bran, rice bran in this compound can be used in 50 percent duck. However, due to the high fat content of rice bran, especially in the summer in the South it is easy to rancidity (5 days or so), so when used in pig feed must pay attention, because the pig is very sensitive sense of smell, can not try to do, you can use cassava to instead. Wheat bran and flour two materials is actually a very easy to rancidity class materials, but many formulators ignores this, so when using wheat bran also pay attention to the freshness of wheat bran, or else there will be poor feeding of animals phenomenon. Fishmeal is a good raw material, but fishmeal adulterated (urea, protein powder) phenomenon is the most serious. There are times I suckling pig feed diarrhea very badly, by reducing the protein, add zinc oxide, citric acid method but the total can not be resolved, then had to take all kinds of raw materials inspection, other raw materials are normal, only fish tested found inside doped ammonium salt. Then put the recipe fishmeal removed, diarrhea problem immediately solved. Because of poor quality fishmeal control, so some companies can buy their dried fish, and then processed into fishmeal. Dried price of 3400 yuan / ton, processing costs 50 yuan / ton, but also cheaper than soybean meal. This not only reduces the cost of fish meal, but also to ensure the quality.
How animal feed making? you can learn from Strongwin feed machinery.Welcome you!
Quality must be noted that the palatability of feed and raw materials
Some formulators do feed formulation, the only mechanical input to the various feed ingredients to the recipe software, and then click on the "linear programming", as long as the formula of nutrients out of reach, and put the recipe and then submitted to a print production on needed. In fact, doing so is extremely irresponsible, although nutritional supplements reached, but feed the "customers" of animals like it or not is really important. Because poor palatability of feed, animal feed will be little or simply refuse to eat. Therefore, selection of raw materials must choose palatability, no deterioration of fresh raw materials. Formulators should not just do a day in the office at the computer to do recipes, each feed must be done in person before a group to look at the quality of raw materials, the necessary time to personally taste raw palatability. There is a feed made out when you want to test it after feed color, smell whether standards. Some feed mills often like to do some anti-stress, and increase lean meat, and promote animal growth of special packet of materials, because relatively speaking, than the obvious effect of this packet of materials, the profit is relatively high. For example, once I do a control mosquito breeding farm parcels material, the main component of this small material called cyromazine, the main role is used to kill mosquitoes eggs. When do such small material cyromazine did not notice the smell is quite unpleasant, just add some carriers and antibiotics in the recipe. The results reflect the customer antifeeding added this little pig feed material, then adjust the recipe when added flavors and sweeteners, then the market reflects this small material has been very good. Another time a similar thing is that some customers complain about our company a small material (main ingredient is yellow amines and amine synergists yellow) growth-promoting effect is not good, then it has increased the amount of two sulfonamides and trimethoprim times, to keep up with examples like the result, or refuse to eat such a small animal feed, the reason is very simple, because these drugs additives have been bad taste and palatability, the time when the amount of the increase will inevitably increase the unpleasant taste, so the sulfonamides and trimethoprim amount to 1.5 times the original amount, but also adds some flavor, so that the effect will be much better formulations.
Stress that it is important to note the quality of feed ingredients, such as rice bran, wheat bran and other raw materials. Fresh rice bran will have a fragrance smells taste in your mouth sweet side, inside a green shell in general are fresh bran rice bran, rice bran in this compound can be used in 50 percent duck. However, due to the high fat content of rice bran, especially in the summer in the South it is easy to rancidity (5 days or so), so when used in pig feed must pay attention, because the pig is very sensitive sense of smell, can not try to do, you can use cassava to instead. Wheat bran and flour two materials is actually a very easy to rancidity class materials, but many formulators ignores this, so when using wheat bran also pay attention to the freshness of wheat bran, or else there will be poor feeding of animals phenomenon. Fishmeal is a good raw material, but fishmeal adulterated (urea, protein powder) phenomenon is the most serious. There are times I suckling pig feed diarrhea very badly, by reducing the protein, add zinc oxide, citric acid method but the total can not be resolved, then had to take all kinds of raw materials inspection, other raw materials are normal, only fish tested found inside doped ammonium salt. Then put the recipe fishmeal removed, diarrhea problem immediately solved. Because of poor quality fishmeal control, so some companies can buy their dried fish, and then processed into fishmeal. Dried price of 3400 yuan / ton, processing costs 50 yuan / ton, but also cheaper than soybean meal. This not only reduces the cost of fish meal, but also to ensure the quality.
How animal feed making? you can learn from Strongwin feed machinery.Welcome you!
Small feed processing unit's match and installment
So-called small feed processing units, which include mainly 3 most: Mills, the lift, mix blender. The matching and installation techniques are as follows:
1, mills Mills is the most commonly used feed processing machinery, the current domestic production the main hammer-mills and roller mills. shredder can be by a variety of different feeding requirements feeding the raw materials into different-sized particles. The machine models are different, and each hour of processing is also different, the motor model is also different. You can fish in accordance with the size to buy. The general chicken coop should be purchased two, one with, - a desktop replacement.
2, blender blender is generally divided into general feed mixers and additive blender. General feed blender has vertical and horizontal. Vertical blender mixing time is typically 15 minutes - 20 minutes, horizontal, is about 10 minutes, the blender with fodder, should call the jar. Vertical blender of benefits is evenly mixed, and power consumption less. The only flaw is a hybrid time is long, low productivity, loading, the material is not sufficient. Bedroom blender main working parts of stirring blades, the blades are both the inside and the outside layers, the spiral in the opposite direction. In the course of their work leaves stirring fodder, so that both the inside and the outside layer feed relatively to mix of purpose. Bedroom blender the advantage of high efficiency, loading, the material quickly, the weakness is that power consumption is large, large footprint, and the price is relatively high, so it is generally more rarely used.
3, the lift lift-to-doo-lift and spiral up the two, in general the spiral lift.
Again, the small feed processing units of the installation. Install feed processing units of the installation order is to install mills, install the motor and drive belt. Blender installed in Mills, the mills of the feed throat with the blender hopper exactly. Raise the connection to hang and mills of the import.
When processing, the main raw materials down, PIT, lift the raw materials to mills, crush, and then given to the people of Blender mixed in the warehouses, and other raw materials to the feed port directly, mixed compartment.
1, mills Mills is the most commonly used feed processing machinery, the current domestic production the main hammer-mills and roller mills. shredder can be by a variety of different feeding requirements feeding the raw materials into different-sized particles. The machine models are different, and each hour of processing is also different, the motor model is also different. You can fish in accordance with the size to buy. The general chicken coop should be purchased two, one with, - a desktop replacement.
2, blender blender is generally divided into general feed mixers and additive blender. General feed blender has vertical and horizontal. Vertical blender mixing time is typically 15 minutes - 20 minutes, horizontal, is about 10 minutes, the blender with fodder, should call the jar. Vertical blender of benefits is evenly mixed, and power consumption less. The only flaw is a hybrid time is long, low productivity, loading, the material is not sufficient. Bedroom blender main working parts of stirring blades, the blades are both the inside and the outside layers, the spiral in the opposite direction. In the course of their work leaves stirring fodder, so that both the inside and the outside layer feed relatively to mix of purpose. Bedroom blender the advantage of high efficiency, loading, the material quickly, the weakness is that power consumption is large, large footprint, and the price is relatively high, so it is generally more rarely used.
3, the lift lift-to-doo-lift and spiral up the two, in general the spiral lift.
Again, the small feed processing units of the installation. Install feed processing units of the installation order is to install mills, install the motor and drive belt. Blender installed in Mills, the mills of the feed throat with the blender hopper exactly. Raise the connection to hang and mills of the import.
When processing, the main raw materials down, PIT, lift the raw materials to mills, crush, and then given to the people of Blender mixed in the warehouses, and other raw materials to the feed port directly, mixed compartment.
2014年10月21日星期二
Feed pellet machine - roller gap adjustment
Roller feed pellet machine (or a roller) gap adjustment is critical for the use of feed pellet machine.
Feed pellet machine for daily use have two kinds, namely flat die feed pellet machine and ring die feed pellet machine two major categories. Roller gap of flat die feed pellet machine adjustment is very simple and intuitive, gap depend directly on the roller at the upper end of the adjusting screw can control the mould pressing wheel, operation boot and feeding test can be carried out.
Ring modes of feed pellet machine is our most commonly used feed pellets, the higher price of the machine. This kind of roller gap adjustment of feed pellet machine relatively trouble. The first is to mould cover is opened, we can see directly is the roller frame plate, roller frame plate at both ends of the two adjusting discs, the screw loosen the fixing disk, or outward to push and pull the disc position, close to the mould is a small gap, away from the die for the large gap. After adjustment, manual rotation of feed pellet machine, with not too tight but can be mutually rub for reference. Then close the cover, switch on the power, test run, if the voice of the normal operation of invest a small amount of raw materials, production test. If the discharge is normal, can be put into production, if the engine abnormal sound or discharging is not smooth, will stop the feed pellet machine, carries on two times of mould pressing roll gap adjustment.
Particularly worth mentioning is that the flat roller gap mold feed pelleting machine and ring modes of feed pellet machine adjustment must comply with current within the rated range, the voice of the normal operation of the feed pellets and smooth discharging these rules. In addition, ring modes of feed pellet machine remember is adjusted in the power-off state, because the operation adjustment will have great danger.
Feed pellet machine manufacturers of professional, experience the use of feed pellet machine of professional Strongwin share with everyone!
Feed pellet machine for daily use have two kinds, namely flat die feed pellet machine and ring die feed pellet machine two major categories. Roller gap of flat die feed pellet machine adjustment is very simple and intuitive, gap depend directly on the roller at the upper end of the adjusting screw can control the mould pressing wheel, operation boot and feeding test can be carried out.
Ring modes of feed pellet machine is our most commonly used feed pellets, the higher price of the machine. This kind of roller gap adjustment of feed pellet machine relatively trouble. The first is to mould cover is opened, we can see directly is the roller frame plate, roller frame plate at both ends of the two adjusting discs, the screw loosen the fixing disk, or outward to push and pull the disc position, close to the mould is a small gap, away from the die for the large gap. After adjustment, manual rotation of feed pellet machine, with not too tight but can be mutually rub for reference. Then close the cover, switch on the power, test run, if the voice of the normal operation of invest a small amount of raw materials, production test. If the discharge is normal, can be put into production, if the engine abnormal sound or discharging is not smooth, will stop the feed pellet machine, carries on two times of mould pressing roll gap adjustment.
Particularly worth mentioning is that the flat roller gap mold feed pelleting machine and ring modes of feed pellet machine adjustment must comply with current within the rated range, the voice of the normal operation of the feed pellets and smooth discharging these rules. In addition, ring modes of feed pellet machine remember is adjusted in the power-off state, because the operation adjustment will have great danger.
Feed pellet machine manufacturers of professional, experience the use of feed pellet machine of professional Strongwin share with everyone!
2014年10月14日星期二
How to implement self-sufficient in livestock feeds?
For cattle and poultry, nutritional standards have been prepared with respect to the genotype, environment, quality of available raw materials, maintenance methods, production and reproduction requirements, production capacity and phase of production.
Many country produces soybean, groundnut, rapeseed, sunflower, sesame and cotton meals and these are used as major ingredients in animal feeds. For animal feeds, soybean is the most frequently used oil seed meal and has completely replaced fish meal in poultry feeds. Cottonseed cake and meal are often used in cattle feed throughout the country. Groundnut meal is less popular because of the aflatoxin problem. Rapeseed meal is second to soybean meal in production and second to cottonseed cake and meal for cattle feed. Sunflower meal is commonly used in both cattle and poultry feed.
Feed particle machine belonging to feed pelleting equipment. Based on corn, feed processing machinery.
soybean meal, straw, grass, rice husk, etc. crushed particles directly compressed
Minimal nutrient loss for feed pellet machine, the machine processing of grain and smooth surface, moderate hardness, degree of internal curing deep penetration. But can kill pathogenic microorganisms and parasites, using a special process, - dry into and dry-out machinery, feed particles in the processing of various additives can be added to the drug, and ensure feed quality. Because dry into and dry out, the water content of less than 12% pellets, convenience store after sealing. Meanwhile gelatinized powder by high temperature condensation under pressure roller extrusion, extruded from the ring mold hole, segmented cutter, and finally get out of the mouth of pellets from the feed, pellet feed naturally cooled before packaging .
Many country produces soybean, groundnut, rapeseed, sunflower, sesame and cotton meals and these are used as major ingredients in animal feeds. For animal feeds, soybean is the most frequently used oil seed meal and has completely replaced fish meal in poultry feeds. Cottonseed cake and meal are often used in cattle feed throughout the country. Groundnut meal is less popular because of the aflatoxin problem. Rapeseed meal is second to soybean meal in production and second to cottonseed cake and meal for cattle feed. Sunflower meal is commonly used in both cattle and poultry feed.
Feed particle machine belonging to feed pelleting equipment. Based on corn, feed processing machinery.
Minimal nutrient loss for feed pellet machine, the machine processing of grain and smooth surface, moderate hardness, degree of internal curing deep penetration. But can kill pathogenic microorganisms and parasites, using a special process, - dry into and dry-out machinery, feed particles in the processing of various additives can be added to the drug, and ensure feed quality. Because dry into and dry out, the water content of less than 12% pellets, convenience store after sealing. Meanwhile gelatinized powder by high temperature condensation under pressure roller extrusion, extruded from the ring mold hole, segmented cutter, and finally get out of the mouth of pellets from the feed, pellet feed naturally cooled before packaging .
THE LIVESTOCK INDUSTRY OF INDIA
India's animal wealth is quite large in terms of its populations of cattle, poultry, sheep and goats, camels, horses and pets (Table 1). Recently, aquaculture has also been growing in importance in India.
Henan Strongwin focus on animal feed machiney,such as feed pellet making machine,and whole machinery on feed pellet production line, of course we also provide pellet plant build service, so if you are interested in feed plant or farming, contact us online or visit our website learn more detail,we are glad to service you.
Table 1
Livestock population in India
Livestock population in India
Livestock type Population (millions)
Cattle 204.5
Buffaloes 84.2
Sheep 50.8
Goats 115.3
Pigs 12.8
Horses/ponies 0.8
Mules 0.2
Donkeys 0.9
Camels 1.0
Yaks 0.06
Mithuns 0.15
Total livestock 470.86
Source: Directorate of Economics and Statistics, Ministry of Agriculture. 1992. Livestock census.Henan Strongwin focus on animal feed machiney,such as feed pellet making machine,and whole machinery on feed pellet production line, of course we also provide pellet plant build service, so if you are interested in feed plant or farming, contact us online or visit our website learn more detail,we are glad to service you.
2014年10月9日星期四
The management of laying hens
Feeding and management measures
1 timely transfer group, timely vaccination, insecticide. Egg into the cage work is best done before 18 weeks of age, in order to make the egg became familiar with the environment. Too late is easy to make the part has opened a production of chicken production, or made into abdominal cavity caused by egg yolk yolk peritonitis. In front of the cage or cage at the same time should be vaccinated with live vaccine of Newcastle disease oil, egg drop syndrome inactivated vaccine and other vaccine. Best to conduct a thorough anthelmintic work into the cage, the method such as mites, lice and other parasites on the body surface of spraying drug available. The body of parasites can be oral albendazole 20 ~ 30 mg / kg body weight, or Fu Ding (Chong Kexing) mix material taking. Transfer group, before and after vaccination in the material should be added in a variety of vitamins, antibiotics to reduce stress reaction.
2 timely conversion laying material. In order to meet the increased demand, the layer reproductive system's weight on the growth and calcium, can begin to feed the feed of laying hens at 18 weeks, 20 weeks of feeding egg laying peak feed. At the same time in the material in an extra times the amount of vitamins. This period shall cancel the method of restricted feeding, make chicken feed freely. Turn on the lights during the guaranteed to have the material groove.
3 increasing illumination time. Rural specialist poultry incubation period with natural illumination method. At 18 weeks of age, if the chickens weight reaches the standard, every two weeks to increase light for 30 minutes, until the egg laying rate reached its peak time as total hours per day or 16 hours until 15. If the chicken is lighter in weight, slow growth, but at the same time increase the feeding until 20 weeks of age increasing illumination time. During egg laying light principle is not shorten the time, intensity can not be weakened.
4 for the chicken to create a comfortable environment conditions. Laying hens in the most suitable temperature is 13 DEG to 23 DEG C, the best winter can be maintained at more than 10 DEG C, the best summer can be maintained at 30 DEG C. To maintain the indoor air circulation, prevent all kinds of noise, keep the environment and feeding, drinking water, light stability.
5 The well prevention disease.
(1) layer into the cage after adding antibiotics in animal feed or drinking water, such as norfloxacin, ciprofloxacin, gentamicin, every 4 ~ 5 weeks administration a week, in order to prevent colibacillosis, salmonellosis, enteritis.
(2) in the feed to add additional regular times the amount of vitamins, in order to adapt to the needs of egg laying chickens and relieve stress reaction, improve the resistance to various diseases.
(3) to strengthen sanitation management, the implementation of reasonable immune procedure, adhere to the disinfection with chicken and environmental disinfection system, prevent epidemics. Pay close attention to the egg laying rate is consistent with the standards, pay close attention to the external environment on the chickens any small effects.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
To combat Egg Chicken-thin shell egg method
Methods for the prevention and control of laying hens eggs with thin shells
(1) adding calcium diet or vitamin D3 observation eggshell thickness changes. If the shell thickness thinning, calcium deficiency; If the eggshell appear deformity, suggesting a lack of vitamin D3, should be properly added.
(2) to adjust the proportion of calcium phosphate in the brood, incubation period, the proportion of calcium phosphate in the 1.5 ~ 2:1, the absorption of calcium and phosphorus utilization rate is higher. Calculation of phosphorus content in the production, we should calculate the effective phosphorus in feed. Plant-based diet, most of the phosphorus in the form of phytic acid phosphorus exist, not easily absorbed by decomposition, so must add phosphates, or adding phytase, to promote the decomposition of phytic acid phosphorus, guarantee of phosphorus in the blood to a certain extent, to keep high gossypol grain in the appropriate proportion of calcium phosphate.
(3) the environmental regulation Should summer birdhouse ventilation cooling, to be warm in winter to keep warm, keep the henhouse appropriate temperature. To strengthen management, keep the henhouse environment quiet, try to reduce stress factors, to create a good environment of egg.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
(1) adding calcium diet or vitamin D3 observation eggshell thickness changes. If the shell thickness thinning, calcium deficiency; If the eggshell appear deformity, suggesting a lack of vitamin D3, should be properly added.
(2) to adjust the proportion of calcium phosphate in the brood, incubation period, the proportion of calcium phosphate in the 1.5 ~ 2:1, the absorption of calcium and phosphorus utilization rate is higher. Calculation of phosphorus content in the production, we should calculate the effective phosphorus in feed. Plant-based diet, most of the phosphorus in the form of phytic acid phosphorus exist, not easily absorbed by decomposition, so must add phosphates, or adding phytase, to promote the decomposition of phytic acid phosphorus, guarantee of phosphorus in the blood to a certain extent, to keep high gossypol grain in the appropriate proportion of calcium phosphate.
(3) the environmental regulation Should summer birdhouse ventilation cooling, to be warm in winter to keep warm, keep the henhouse appropriate temperature. To strengthen management, keep the henhouse environment quiet, try to reduce stress factors, to create a good environment of egg.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
2014年9月30日星期二
How raises pigs can make money
Year a net profit of 350 yuan pig slaughter 260 pigs profit more than 80,000 yuan.
First, since the fan from fertility to the market to buy piglets, more expensive, year, for example, a 10 kg weight piglet price is about 200 yuan, increasing farming costs, resulting in relatively less profitable, while piglets reproduction of self-education, there 6 sows and a boar Shylock, the production of piglets reared basically meet its own needs, saving nearly a million from the piglets.
Second, ecological farming manure as raw biogas, biogas slurry as fertilizer corn, corn and processed into pig feed, recycling ecological chain thus formed, full use of the resources, cost savings is equivalent to increasing the efficiency, feed just one year savings over 8000 yuan.
Third place self-control epidemic disease prevention Miebing technology pigs, the pigs will not plague occur, usually farmed five months or so you can slaughter, the measures to avoid losses caused by pig disease.
Fourth, self-made feed 20 acres of land will be fully planted corn, can produce more than 1.50 million kg of corn per year, the corn after processing, the use of technology at their disposal, along with corn and other feed made of compound feed, pig love, long fast, pig meat is good, popular in the market. so do you have build your own feed production line now?
Fifth-scale farming investment 60,000 yuan build capacity for 160 farms, feeding two batches per year, a total of about 300, the advantage of scale and become large pig, ability to withstand market risks, the relative price of pigs small family run slightly more astute.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
First, since the fan from fertility to the market to buy piglets, more expensive, year, for example, a 10 kg weight piglet price is about 200 yuan, increasing farming costs, resulting in relatively less profitable, while piglets reproduction of self-education, there 6 sows and a boar Shylock, the production of piglets reared basically meet its own needs, saving nearly a million from the piglets.
Second, ecological farming manure as raw biogas, biogas slurry as fertilizer corn, corn and processed into pig feed, recycling ecological chain thus formed, full use of the resources, cost savings is equivalent to increasing the efficiency, feed just one year savings over 8000 yuan.
 |
| animal feed pellet production line |
Fourth, self-made feed 20 acres of land will be fully planted corn, can produce more than 1.50 million kg of corn per year, the corn after processing, the use of technology at their disposal, along with corn and other feed made of compound feed, pig love, long fast, pig meat is good, popular in the market. so do you have build your own feed production line now?
Fifth-scale farming investment 60,000 yuan build capacity for 160 farms, feeding two batches per year, a total of about 300, the advantage of scale and become large pig, ability to withstand market risks, the relative price of pigs small family run slightly more astute.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
2014年9月27日星期六
Cattle pasture poisoning mention mildew
Save poor pasture, often moldy, especially during rainy weather even hit the summer and autumn stacking, center and bottom of the haystack is often a lot of fungal growth, cattle feed this part of the forage, there will be symptoms of poisoning. Cattle poisoning caused by the fungus Fusarium toxins mainly. Fusarium may be parasitic on rice straw, wheat straw, sweet potato vine, peanut vine and a variety of grass.
Cow performance mycotoxins major role in livestock peripheral vascular, so that
the local vascular spasm contraction, resulting in wall thickening, stenosis, causing slow blood flow and thrombosis, edema, bleeding and muscle deformation, necrosis, if secondary bacterial infection, the condition will worsen, ball joints less serious can rot. The disease is often sudden, cow gait stiff, careful observation will find hoof crown slightly swollen, the skin has a transverse fissure recess, slightly hot, there is pain. A few days later, the swelling department will spread to the wrist or tarsal joints, difficulty walking. Subsequently, the swollen skin cool, pale yellow liquid oozing surface. If you continue to develop, after the swelling skin ulceration, leading to bleeding, purulent, necrosis, eventually becoming wound healing, unpleasant stench. Serious hoof box may fall off. Apex and the tip of the tail part of some cows, there will be dry necrosis, skin dry and hard, showing dark black.
Prevention
First, access to pasture when the bottom of the haystack, pay attention to check and found that agglomeration rotten forage should be abandoned as soon as possible.
Two, to observe the herd, found a cow hoof lesions appear limb should be carefully checked to determine if the pasture belonging to mold poisoning, should be changed to feed high quality hay, feed while feeding sprout, cabbage, radishes, carrots, etc., to supplement the vitamins enhance the appetite.
Third, timely treatment cows. Early stages, to promote blood circulation, should be hot limb, apply 2 to 3 times a day, every 30 minutes, and 20 to 30 grams of white pepper and white wine mixed with 200 to 300 ml, once fed. Ulceration of the skin, to timely use of 0.1% benzalkonium bromide solution to clean the wound, and then spreading topical sulfa drugs, but also with the use of antibiotics for treatment. In order to promote granulation tissue and epithelial hyperplasia, accelerate healing sores, can be coated erythromycin ointment affected area 1-2 times a day. For serious illness, intravenous injection of 5% glucose solution 1000 to 2000 ml.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
Cow performance mycotoxins major role in livestock peripheral vascular, so that
Prevention
First, access to pasture when the bottom of the haystack, pay attention to check and found that agglomeration rotten forage should be abandoned as soon as possible.
Two, to observe the herd, found a cow hoof lesions appear limb should be carefully checked to determine if the pasture belonging to mold poisoning, should be changed to feed high quality hay, feed while feeding sprout, cabbage, radishes, carrots, etc., to supplement the vitamins enhance the appetite.
Third, timely treatment cows. Early stages, to promote blood circulation, should be hot limb, apply 2 to 3 times a day, every 30 minutes, and 20 to 30 grams of white pepper and white wine mixed with 200 to 300 ml, once fed. Ulceration of the skin, to timely use of 0.1% benzalkonium bromide solution to clean the wound, and then spreading topical sulfa drugs, but also with the use of antibiotics for treatment. In order to promote granulation tissue and epithelial hyperplasia, accelerate healing sores, can be coated erythromycin ointment affected area 1-2 times a day. For serious illness, intravenous injection of 5% glucose solution 1000 to 2000 ml.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
The three elements of scientific raising pigs
Science is of three elements: a good pig: appropriate temperature, humidity and light.
The suitable growth temperature of newborn piglets is 34 ℃ ~ 35 ℃;3 ~ 4 weeks of piglet suitable growth temperature is about 30 ℃;Larger piglet suitable growth temperature is 20 ℃ ~ 23 ℃;A pig growth of optimum temperature is 17 ℃ ~ 22 ℃.Under the appropriate temperature, the growth of pig carcass fat and lean meat is normal, in the high temperature and low temperature environment, slow growth of the fat.When raising lean hogs, therefore, should try to give the pig to create appropriate temperature environment.
The condition of high temperature, high humidity may slow down weight to pigs, with a high mortality rate.Under the condition of low temperature, high humidity, get heat intensifying, the pig weight decreased by 36%, litter size decreased by 28%, per kilogram weight loss is expected to increase by 10%.
Mild and moderate light, good for growth of young pigs and pig breeding.Young pigs often contact sunshine, can strengthen the blood circulation, accelerate metabolism, promote cell proliferation and bone growth, increase the speed of development.Sows, often exposed to direct sunlight can accelerate the development of the egg, promoting estrus ovulation, increase fertility.But the illumination time is too long, easy to make pig activity increases, have an effect on weight gain.
In addition, also has effect on the normal fertility of airflow to the pig.Good air convection in piggery, when high temperature cooling;If the air circulation, adverse to the pig, low temperature, airflow into the cold, but also to the pig.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
The condition of high temperature, high humidity may slow down weight to pigs, with a high mortality rate.Under the condition of low temperature, high humidity, get heat intensifying, the pig weight decreased by 36%, litter size decreased by 28%, per kilogram weight loss is expected to increase by 10%.
Mild and moderate light, good for growth of young pigs and pig breeding.Young pigs often contact sunshine, can strengthen the blood circulation, accelerate metabolism, promote cell proliferation and bone growth, increase the speed of development.Sows, often exposed to direct sunlight can accelerate the development of the egg, promoting estrus ovulation, increase fertility.But the illumination time is too long, easy to make pig activity increases, have an effect on weight gain.
In addition, also has effect on the normal fertility of airflow to the pig.Good air convection in piggery, when high temperature cooling;If the air circulation, adverse to the pig, low temperature, airflow into the cold, but also to the pig.
Henan Strongwin machinery is a professional feed machinery, feed production line manufacturer, we offer a variety of feed production equipment, whether you are to have their own farms, or would like to establish a feed production plant, you can contact us. We are happy to serve you.
2014年9月25日星期四
Chicken money? Chicken human experience and experience sharing
Chicken money? Many novice and prepare chicken friends will have this question, "Why do I chicken makes money," for many years as a chicken farmer, I have not had a loss of records, including the flu that year I like to avoid the risk, calmly chicken to make money, I put some of my experiences say immature total share:
A peasant farming 80 is blind, and earn loss loss, it is common, the real reason is the loss:
1 raise bad chicken,
2 did not keep a good chicken spotted market,
And these two points is still a little law can find, but most households raise chickens never sober analysis, like gambling, watching a chicken so luck would like to make money is very dangerous.
Second, keep a good start with chicken, good technology is not necessarily able to keep a good chicken, you let those experts and professors to chickens, they will still be dead raised, chicken want is advanced and accurate management technology, or those large farming companies have technicians why so many managers still paying please, that we ordinary small-raising households is the same management is more important than technology
Third, not all of them are suitable for chicken, chicken requires a high degree of responsibility and are not afraid of bitter spirit, if you are naturally lazy, like every day, play cards, or drink, then do not enter this industry, so fill it burn, or leave some money playing cards, drinking good livestock to earn money, to sleep with livestock, but the saying has truth, I raised the white feather of 50 days is to stay in the countryside never go out, it is the principle of chicken.
pellet feed unit increase the particle section on the basis of producing powder feed compelete sets of equipment.particles section equipment mainly includes particle machine,cooler, crushed machine, grader,packaging scale etc.
A peasant farming 80 is blind, and earn loss loss, it is common, the real reason is the loss:
1 raise bad chicken,
2 did not keep a good chicken spotted market,
And these two points is still a little law can find, but most households raise chickens never sober analysis, like gambling, watching a chicken so luck would like to make money is very dangerous.
Second, keep a good start with chicken, good technology is not necessarily able to keep a good chicken, you let those experts and professors to chickens, they will still be dead raised, chicken want is advanced and accurate management technology, or those large farming companies have technicians why so many managers still paying please, that we ordinary small-raising households is the same management is more important than technology
Third, not all of them are suitable for chicken, chicken requires a high degree of responsibility and are not afraid of bitter spirit, if you are naturally lazy, like every day, play cards, or drink, then do not enter this industry, so fill it burn, or leave some money playing cards, drinking good livestock to earn money, to sleep with livestock, but the saying has truth, I raised the white feather of 50 days is to stay in the countryside never go out, it is the principle of chicken.
pellet feed unit increase the particle section on the basis of producing powder feed compelete sets of equipment.particles section equipment mainly includes particle machine,cooler, crushed machine, grader,packaging scale etc.
2014年9月22日星期一
How efficient breeding sheep? Sheep farming techniques (one)
Select varieties to local conditions:
Good sheep breed large size, fast growth, reproduction rate, adaptability, good meat quality, high efficiency, mainly goats, Saanen goats, the Huang-Huai goats. Now most of the local breeds of goats reared mainly small individual, slow growth, slaughter rate, so the efficiency is not high. To reverse this situation, should be introduced goats, Saanen goats crossbreeding. For example, the Boer goat and local goat hybrid, at 6 months of age weight gain than the local sheep nearly 10 kg, can significantly improve efficiency.
Good sheep breed large size, fast growth, reproduction rate, adaptability, good meat quality, high efficiency, mainly goats, Saanen goats, the Huang-Huai goats. Now most of the local breeds of goats reared mainly small individual, slow growth, slaughter rate, so the efficiency is not high. To reverse this situation, should be introduced goats, Saanen goats crossbreeding. For example, the Boer goat and local goat hybrid, at 6 months of age weight gain than the local sheep nearly 10 kg, can significantly improve efficiency.
 |
| feed pellet machine |
How fast and efficient high-yield farming grass carp ?
In the past conventional breeding carp polyculture are mainly three years to develop, the high cost of funds used a long time. The author summarizes the promotion of a pollution-free grass yield fast and efficient farming techniques, are presented below.
1, Pond Requirements: 10-20 acres suitable pond area, depth 2-2.5 m, silt thickness of not more than 20 cm. Per 10 acres pond supporting power of 3 kW aerators and automatic feeding machine of a desk.
2, pond clearing: Winter draining of water, freeze drying more than 20 days. 15 days ago fish stocking, water 10-20 cm, 150 kg of lime per acre clear pond disinfection.
3, fish stocking: before and after the Spring Festival, put specifications for 200-250 grams per acre grass seed / tail 300, specifications for 15-20 tail / kg of carp species 300, Specifications for 5-6 fish / kg of silver carp 50 species, bighead carp species 10. Before fish stocking with 5% salt water immersion disinfection 5-10 minutes.
4, feed feeding: feeding pellets to the main feed protein content of 28-32%, the secondary cast green feed. Feed fed to follow "four four to see" principle "after former coarse fine" and, generally fed two times a day, to within two hours after eating, grass carp feeding eight full appropriate. March-June to ration protein content of 28% of the pellets based, daily feeding rate of 3%, moderate fed green fodder; July to September, the control pellet feed ration, daily feeding rate of 1.5% so, pellet feed protein content of 28%, and increase the amount of green fodder fed to control fish disease; October-November fed protein content of 32% of the pellets. After a period of continuous feeding pellets should stop feeding pellets one week, feeding unprocessed feed during the interval. Usually pay attention to add the appropriate amount of vitamins in feed and other drugs, to avoid the risk of grass carp hepatobiliary syndrome and other diseases caused by a large number of deaths.
5, Water Quality Management: Proper use of aerators, sunny windless weather from June to October, 1-3 pm every boot aerobics two hours, morning aerobics timely; consecutive cloudy days should be ahead of oxygen. Timely to raise new water pond, to take "a small row of small forward, changing the water several times" approach to gradually regulate water quality. June to September, filling the new water every 3-5 days a times, each about 10 cm of water every 15-20 days per acre with water one meter depth of 10-20 kg of lime slurry Quanchiposa 1 .
6, disease control: the use of "coarse ago after fine, fine green combination" approach feeding, control grass hepatobiliary syndrome occur. Common carp have red skin disease, gill disease, enteritis disease, in general, the treatment combination of oral spilled outside, outside throwing mainly in bleaching powder, chlorine dioxide disinfectant based, once every three days; Oral "Three gluten "bait better, per 50 kilograms of fish reuse three rhubarb (Rheum 50%, Cork 30%, skullcap 20%, after crushed Powder mix) after 0.3 kilograms of flour paste mixed ration feed mix , 3-5 days.
7, timely harvest: timely listing of the large size of adult fish farming is an important measure yielding grass harvesting, the main purpose is to reduce the load of fish pond water volume, and promote rapid growth of the latter part of the fish. Usually ships since the end of July to catch a second, lower water temperatures in the morning harvesting.
Henan Strongwin Machinery is a professional manufacturer of feed pellet machine production and we can supply the solution on total feed production line build.
1, Pond Requirements: 10-20 acres suitable pond area, depth 2-2.5 m, silt thickness of not more than 20 cm. Per 10 acres pond supporting power of 3 kW aerators and automatic feeding machine of a desk.
2, pond clearing: Winter draining of water, freeze drying more than 20 days. 15 days ago fish stocking, water 10-20 cm, 150 kg of lime per acre clear pond disinfection.
3, fish stocking: before and after the Spring Festival, put specifications for 200-250 grams per acre grass seed / tail 300, specifications for 15-20 tail / kg of carp species 300, Specifications for 5-6 fish / kg of silver carp 50 species, bighead carp species 10. Before fish stocking with 5% salt water immersion disinfection 5-10 minutes.
4, feed feeding: feeding pellets to the main feed protein content of 28-32%, the secondary cast green feed. Feed fed to follow "four four to see" principle "after former coarse fine" and, generally fed two times a day, to within two hours after eating, grass carp feeding eight full appropriate. March-June to ration protein content of 28% of the pellets based, daily feeding rate of 3%, moderate fed green fodder; July to September, the control pellet feed ration, daily feeding rate of 1.5% so, pellet feed protein content of 28%, and increase the amount of green fodder fed to control fish disease; October-November fed protein content of 32% of the pellets. After a period of continuous feeding pellets should stop feeding pellets one week, feeding unprocessed feed during the interval. Usually pay attention to add the appropriate amount of vitamins in feed and other drugs, to avoid the risk of grass carp hepatobiliary syndrome and other diseases caused by a large number of deaths.
5, Water Quality Management: Proper use of aerators, sunny windless weather from June to October, 1-3 pm every boot aerobics two hours, morning aerobics timely; consecutive cloudy days should be ahead of oxygen. Timely to raise new water pond, to take "a small row of small forward, changing the water several times" approach to gradually regulate water quality. June to September, filling the new water every 3-5 days a times, each about 10 cm of water every 15-20 days per acre with water one meter depth of 10-20 kg of lime slurry Quanchiposa 1 .
6, disease control: the use of "coarse ago after fine, fine green combination" approach feeding, control grass hepatobiliary syndrome occur. Common carp have red skin disease, gill disease, enteritis disease, in general, the treatment combination of oral spilled outside, outside throwing mainly in bleaching powder, chlorine dioxide disinfectant based, once every three days; Oral "Three gluten "bait better, per 50 kilograms of fish reuse three rhubarb (Rheum 50%, Cork 30%, skullcap 20%, after crushed Powder mix) after 0.3 kilograms of flour paste mixed ration feed mix , 3-5 days.
7, timely harvest: timely listing of the large size of adult fish farming is an important measure yielding grass harvesting, the main purpose is to reduce the load of fish pond water volume, and promote rapid growth of the latter part of the fish. Usually ships since the end of July to catch a second, lower water temperatures in the morning harvesting.
Henan Strongwin Machinery is a professional manufacturer of feed pellet machine production and we can supply the solution on total feed production line build.
Feed pellet machine advantages
Feed pellet machine advantages:
1. Simple structure, wide adaptability, cover an area of an area small, low noise.
2. The powder feed, toppings do not need or with a little liquid can be added for granulating, so basic as the moisture content of grain feed granulating before the moisture content of materials, more conducive to storage.
3. The chicken, duck, fish, etc., than the mixed powder feed can obtain higher economic benefits.
4. Dry processing, the production of feed particle high hardness, smooth surface, internal curing, can improve the digestion and absorption of nutrients.
5. Particle formation can cause the pancreatic enzyme boycott factor in the grains, legumes degeneration effect, reduce the adverse effects on the digestive, can kill all kinds of parasitic ovum and other pathogenic microorganisms, reduce all kinds of insect and diseases of the digestive system.
 |
| ring die feed pellet machine |
2. The powder feed, toppings do not need or with a little liquid can be added for granulating, so basic as the moisture content of grain feed granulating before the moisture content of materials, more conducive to storage.
3. The chicken, duck, fish, etc., than the mixed powder feed can obtain higher economic benefits.
4. Dry processing, the production of feed particle high hardness, smooth surface, internal curing, can improve the digestion and absorption of nutrients.
5. Particle formation can cause the pancreatic enzyme boycott factor in the grains, legumes degeneration effect, reduce the adverse effects on the digestive, can kill all kinds of parasitic ovum and other pathogenic microorganisms, reduce all kinds of insect and diseases of the digestive system.
2014年9月17日星期三
Way to increase the utilization ratio of straw feed
Mineral and vitamin supplements
1. Mineral supplement
Straw and body growth in many mineral elements contents are related to the lack of long-term feeding of these straws is bound to affect the growth and health of livestock. Need to add minerals include calcium, phosphorus, sulfur, zinc, selenium, cobalt, etc.
(L) straw of calcium and phosphorus in calcium and phosphorus content is low, particularly phosphorus content is extremely low, 0.02%~0.16, well below the needs of growth and reproduction in ruminant (cattle and sheep on the dietary phosphorus requirements of about 0.3%). Therefore, generally need to add phosphorus in feeds mainly based on straw, calcium supplementation. But straw, because of their silicate content of up to around 17%, affect the absorption and utilization of calcium, can cause negative calcium balance, and calcium should be added.
(2) the sulfur sulfur amino acid composition of rumen microbes can use non-protein nitrogenous compounds sulfur inorganic synthesis of sulfur-containing amino acids, sulfur also has a good role in cellulose digestion. So when cattle and sheep fed urea, sulfur should be added per kilogram of dietary sulfur 2 g of dry matter, nitrogen per gram or the number of 0.1 grams of sulfur.
(3) zinc and cobalt and zinc are important components of various types of casein, directly involved in the synthesis and metabolism of proteins and nucleic acids, promote the metabolism of glycogen; Cobalt are vitamin B12 (cobalamin) the main ingredient, in the role of rumen microbes, in the synthesis of vitamin B12. Zinc and cobalt content in stalks are very low, unable to meet the body's needs, therefore, in feeding straw feed must be added zinc and cobalt. Generally speaking, the suitable amount of cobalt in the diet of 0.5~1 mg/kg of dry matter, sufficient quantity of zinc 40~100 NG Peng kg dry matter.
2. vitamin supplement
Vitamins can be classified into fat-soluble vitamins (vitamin a, vitamin d) and water soluble vitamins (vitamin b, vitamin c, vitamin k, and vitamin e) two broad categories. Adult bovine rumen can synthesize vitamin b and vitamin k, vitamin c can be synthesized in the liver and kidneys. Therefore, apart from suckling calves, these vitamins is not usually necessary to add another. Straw to feed cattle and sheep, you generally need to add vitamins a, vitamin d, and vitamin e, especially should pay attention to add Nicotinic Acid high producing dairy cows.
1. Mineral supplement
Straw and body growth in many mineral elements contents are related to the lack of long-term feeding of these straws is bound to affect the growth and health of livestock. Need to add minerals include calcium, phosphorus, sulfur, zinc, selenium, cobalt, etc.
(L) straw of calcium and phosphorus in calcium and phosphorus content is low, particularly phosphorus content is extremely low, 0.02%~0.16, well below the needs of growth and reproduction in ruminant (cattle and sheep on the dietary phosphorus requirements of about 0.3%). Therefore, generally need to add phosphorus in feeds mainly based on straw, calcium supplementation. But straw, because of their silicate content of up to around 17%, affect the absorption and utilization of calcium, can cause negative calcium balance, and calcium should be added.
(2) the sulfur sulfur amino acid composition of rumen microbes can use non-protein nitrogenous compounds sulfur inorganic synthesis of sulfur-containing amino acids, sulfur also has a good role in cellulose digestion. So when cattle and sheep fed urea, sulfur should be added per kilogram of dietary sulfur 2 g of dry matter, nitrogen per gram or the number of 0.1 grams of sulfur.
(3) zinc and cobalt and zinc are important components of various types of casein, directly involved in the synthesis and metabolism of proteins and nucleic acids, promote the metabolism of glycogen; Cobalt are vitamin B12 (cobalamin) the main ingredient, in the role of rumen microbes, in the synthesis of vitamin B12. Zinc and cobalt content in stalks are very low, unable to meet the body's needs, therefore, in feeding straw feed must be added zinc and cobalt. Generally speaking, the suitable amount of cobalt in the diet of 0.5~1 mg/kg of dry matter, sufficient quantity of zinc 40~100 NG Peng kg dry matter.
2. vitamin supplement
Vitamins can be classified into fat-soluble vitamins (vitamin a, vitamin d) and water soluble vitamins (vitamin b, vitamin c, vitamin k, and vitamin e) two broad categories. Adult bovine rumen can synthesize vitamin b and vitamin k, vitamin c can be synthesized in the liver and kidneys. Therefore, apart from suckling calves, these vitamins is not usually necessary to add another. Straw to feed cattle and sheep, you generally need to add vitamins a, vitamin d, and vitamin e, especially should pay attention to add Nicotinic Acid high producing dairy cows.
2014年9月16日星期二
Why feed particle machine will appear uneven particle size
When we rural animal it is necessary to pay attention to, have why many customers to our response with pellet machine that feed size are not uniform, and some corn or even inside are crushed to have several customers, after many experiments still appear this kind of problem, ask we are problems not pellet machine through expert analysis, and field survey and draw a few conclusions, mainly due to blade gear granule machine problems and motor problems.
Processing we use feed pellet machine purpose is for some of the material, if this item is not well done so more may not do, feed particle machine after sale service is very important, if appear this kind of problem should be timely contact the manufacturer, to find the corresponding measures, if go down for a long time will greatly shorten his life, but also thousands of pieces of a particle machine at least, to tens of thousands of pieces of the most, so the face of expensive particle machine should protect and use the good.
When we must pay attention to the rural culture, the use of animal feed particle machine brings much convenience as well as output increases greatly for us, but how to do this line is also on the auxiliary mechanical, we invested a lot of these machinery also want to increase our production, particle machine indeed played a very big role in a row.
There are also many times we are at home or in the operation of particles when some enterprises machine not serious cause, why do you say so, appear uneven granule question one is due to particle is too wet, even have a lot of materials are just like some of the corn harvest, like, just to produce them from the ground Li, not dry construction began particle machine, so the result of particles of the host machine seriously pressed, gear long time running down the host is very slow, and the blade is very dull, so caused a lot of particle size.
Processing we use feed pellet machine purpose is for some of the material, if this item is not well done so more may not do, feed particle machine after sale service is very important, if appear this kind of problem should be timely contact the manufacturer, to find the corresponding measures, if go down for a long time will greatly shorten his life, but also thousands of pieces of a particle machine at least, to tens of thousands of pieces of the most, so the face of expensive particle machine should protect and use the good.
When we must pay attention to the rural culture, the use of animal feed particle machine brings much convenience as well as output increases greatly for us, but how to do this line is also on the auxiliary mechanical, we invested a lot of these machinery also want to increase our production, particle machine indeed played a very big role in a row.
There are also many times we are at home or in the operation of particles when some enterprises machine not serious cause, why do you say so, appear uneven granule question one is due to particle is too wet, even have a lot of materials are just like some of the corn harvest, like, just to produce them from the ground Li, not dry construction began particle machine, so the result of particles of the host machine seriously pressed, gear long time running down the host is very slow, and the blade is very dull, so caused a lot of particle size.
2014年9月15日星期一
Feed pellet mill-----small machines play a bigger role
Now many farmers are beginning to use feed pellets. Pellets come by? What was good?
Zhang Uncle is a professional farmers. Recently something happened, but the uncle were overjoyed. Uncle from newly acquired a pig feed pellet mill to begin. Zhang Uncle told this reporter, "self now use this feed mill for pig feed, money and peace of mind. Previously worrying about the market for pig feed is bad, now make their own feed, no longer have to worry about it now. Most importantly do it yourself out of such pigs pigs love to eat. "
Pig feed pellet mill is the agricultural residues such as straw, peanut shells and mixing, it is a machine made of pig feed pellets by high temperature. Coupled with the pig feed pellet mill structure is simple, the operation is very convenient, especially if a small pig feed pellet mill is suitable for use in small and medium pig farmers.
Produced by pig feed pellet mill pellets like regular fodder for pigs, what are so different, why do animals like to eat?
According to industry stakeholders, from pig feed pellet mill production out of pig feed in the production process at high temperature can kill germs, the pigs sick rate reduction. And compacting process by mixing the starch gelatinization, easy to pig's digestive tract. Plus produce pig feed pellets contain a natural grass, pigs will love to eat.
I learned and visited a number of pig farms, pig feed pellet mill has been quietly popular in the pig industry, most people have purchased or have plans to buy. Strongwin technician told me that the "pig feed pellet mill use the fat from some straw, peanut shells, weeds, and much of this stuff is in the countryside. This saves a pig out of a lot of cost, and for them to solve the issue of straw use."
Zhang Uncle is a professional farmers. Recently something happened, but the uncle were overjoyed. Uncle from newly acquired a pig feed pellet mill to begin. Zhang Uncle told this reporter, "self now use this feed mill for pig feed, money and peace of mind. Previously worrying about the market for pig feed is bad, now make their own feed, no longer have to worry about it now. Most importantly do it yourself out of such pigs pigs love to eat. "
Pig feed pellet mill is the agricultural residues such as straw, peanut shells and mixing, it is a machine made of pig feed pellets by high temperature. Coupled with the pig feed pellet mill structure is simple, the operation is very convenient, especially if a small pig feed pellet mill is suitable for use in small and medium pig farmers.
Produced by pig feed pellet mill pellets like regular fodder for pigs, what are so different, why do animals like to eat?
According to industry stakeholders, from pig feed pellet mill production out of pig feed in the production process at high temperature can kill germs, the pigs sick rate reduction. And compacting process by mixing the starch gelatinization, easy to pig's digestive tract. Plus produce pig feed pellets contain a natural grass, pigs will love to eat.
I learned and visited a number of pig farms, pig feed pellet mill has been quietly popular in the pig industry, most people have purchased or have plans to buy. Strongwin technician told me that the "pig feed pellet mill use the fat from some straw, peanut shells, weeds, and much of this stuff is in the countryside. This saves a pig out of a lot of cost, and for them to solve the issue of straw use."
2014年9月11日星期四
The use of feed pellet mill
With the rapid development of animal husbandry and aquaculture to promote and popularize the use of feed pellet mill make a huge space for development. With artificial feed on livestock in the promotion and popularization of feed pellet mill for animal husbandry and aquaculture provided a strong impetus for the development, more and more farmers to buy the feed pellet mill pellets at its production. Henan Strongwin machinery are engaged in development of feed processing equipment development for many years, for the ratio of pellet feed control detailed recipe, available free of charge to farmers and processing pellet feed.
Advantages of pellet feed machine
a, within pressure roller and die plate at both ends, consistent with the outer wire-speed, does not appear misplaced friction wheel and die, reducing drag, reducing the kinetic energy loss, to extend the life of the mold, reducing production costs.
b, uniform pressure roller set, smooth operation, improve production efficiency.
c, using spiral stalk regulator structure, die big gap with the small, adapted to different materials to ensure the suppression effect.
Advantages of pellet feed machine
a, within pressure roller and die plate at both ends, consistent with the outer wire-speed, does not appear misplaced friction wheel and die, reducing drag, reducing the kinetic energy loss, to extend the life of the mold, reducing production costs.
b, uniform pressure roller set, smooth operation, improve production efficiency.
c, using spiral stalk regulator structure, die big gap with the small, adapted to different materials to ensure the suppression effect.
2014年9月10日星期三
Feed for livestock feed pellet mill manufacturing benefits
Feed pellet mill has been so widely used, partly because feed pellet mill's own environmental protection there is to use pellet feed for livestock is really good.
1. feeding pellet feed better than the dry powder materials, as is the result of the maturing of pellet feed granulation, feed easier to digest, easy feeding, small loss, not moldy, palatability, feed intake.
2. nutrition can handle on your own.
3. reduce farming costs.
4. animals can eat the freshest feed at any time.
Economical and practical, small, great income, many favorable factors have prompted more farmers to choose the feed pellet mill!
1. feeding pellet feed better than the dry powder materials, as is the result of the maturing of pellet feed granulation, feed easier to digest, easy feeding, small loss, not moldy, palatability, feed intake.
2. nutrition can handle on your own.
3. reduce farming costs.
4. animals can eat the freshest feed at any time.
Economical and practical, small, great income, many favorable factors have prompted more farmers to choose the feed pellet mill!
Feed pellet mill selection techniques
Currently, the feed pellet mill not only many brands on the market, price-quality is very different from many, this caused some troubles to consumer purchasing. today, small series to teach you a few tips for selecting feed pellet mill.
Select feed pellet mill, according to auxiliary power: instruction manual and on the nameplate of the machine containing the feed pellet mill auxiliary power of electric motor kW.
Second, according to the production capacity of selected feed pellet mill: General description of feed pellet mill and nameplate, are contained within the feed pellet mill capacity rating. However, you should note several points:
a. contained in rated capacity refers to the output of a particular State.
b. selected feed particles machine of capacity should slightly is greater than actual needs of capacity. Three, and according to crushed material select feed particles machine: to crushed grain feed mainly of, can select top Department into material of hammer tablets type feed particles machine; to crushed bran bran Valley wheat class feed mainly of, can select claw type feed particles machine; crushed shells, mineral feed, can selection shells no sieve type feed particles machine; if as pre mixed feed of pre-press processing, should selection special no sieve type feed particles machine,.
Select feed pellet mill, according to auxiliary power: instruction manual and on the nameplate of the machine containing the feed pellet mill auxiliary power of electric motor kW.Second, according to the production capacity of selected feed pellet mill: General description of feed pellet mill and nameplate, are contained within the feed pellet mill capacity rating. However, you should note several points:
a. contained in rated capacity refers to the output of a particular State.
b. selected feed particles machine of capacity should slightly is greater than actual needs of capacity. Three, and according to crushed material select feed particles machine: to crushed grain feed mainly of, can select top Department into material of hammer tablets type feed particles machine; to crushed bran bran Valley wheat class feed mainly of, can select claw type feed particles machine; crushed shells, mineral feed, can selection shells no sieve type feed particles machine; if as pre mixed feed of pre-press processing, should selection special no sieve type feed particles machine,.
订阅：
博文 (Atom)